[gentoo-user] Gentoo 2004.3 hang while rebooting on Compaq ap400

[gentoo-user] Gentoo 2004.3 hang while rebooting on Compaq ap400

[Marcin Lolownik]

Hello.

I have installed Gentoo 2004.3 from live cd on 2-cpu Compaq 'Professional Desktop AP400'.
[dmesg's and other info attached below the post]
When I run shutdown -r now from Live CD the system warm-reboot's without any
problems.
Unfortunately, when I've built a mandatory kernel, when doing shutdown the
system goes to appropriate runlevel, unmount's disk's etc., the screen goes
blank and the machine hangs, until i manually power it off and back on.

I spent several hours trying to tune options in kernel config's power management
and kernel's 'reboot' parameter with no good effects.

Where can i found what configuration/sources/patches were used to build kernel
on 2004.3 live cd?

Can You help me/point to doc/etc. ? I've ran out of ideas.
I'll provide any extra info on demand.

uname -a
Linux gen 2.6.9-gentoo-r4 #5 SMP Thu Dec 2 18:14:02 CET 2004 i686 Pentium II (Deschutes) GenuineIntel GNU/Linux

dmesg and my kernel config are below and here:
- http://messy.desk.pl/dmesg
- http://messy.desk.pl/config-2.6.9-gnetoo-r4
There is also dmesg from the live cd:
- http://messy.desk.pl/cd.dmesg
and a diff between the two: 
- http://messy.desk.pl/dmesg.diff
(Didn't want to send too much to the list.)
I can Provide You with info from /proc, but I'm not sure which files can be 
helpfull.

Linux version 2.6.9-gentoo-r4 (root@gen) (gcc version 3.3.4 20040623 (Gentoo Linux 3.3.4-r1, ssp-3.3.2-2, pie-8.7.6)) #5 SMP Thu Dec 2 18:14:02 CET 2004
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000014000000 (usable)
 BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
320MB LOWMEM available.
found SMP MP-table at 000f6420
On node 0 totalpages: 81920
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 77824 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
DMI not present.
ACPI: RSDP (v000 COMPAQ                                ) @ 0x000ec010
ACPI: RSDT (v001 COMPAQ LAREDO   0x00000001  0x00000000) @ 0x000ec080
ACPI: FADT (v001 COMPAQ LAREDO   0x00000001  0x00000000) @ 0x000ec0cc
ACPI: MADT (v001 COMPAQ LAREDO   0x00000001  0x00000000) @ 0x000ec140
ACPI: SSDT (v001 COMPAQ VILLTBL1 0x00000001 MSFT 0x01000007) @ 0x000ecc5b
ACPI: SSDT (v001 COMPAQ PNP_PRSS 0x00000001 MSFT 0x01000007) @ 0x000ed830
ACPI: DSDT (v001 COMPAQ     DSDT 0x00000001 MSFT 0x01000007) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:5 APIC version 17
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:5 APIC version 17
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
ACPI: NMI_SRC (dfl dfl global_irq 1)
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/sda1
Initializing CPU#0
CPU 0 irqstacks, hard=c046c000 soft=c046a000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 399.177 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 320504k/327680k available (2355k kernel code, 6760k reserved, 911k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 786.43 BogoMIPS (lpj=393216)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183fbff 00000000 00000000 00000000
CPU: After vendor identify, caps:  0183fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After all inits, caps:        0183fbff 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
CPU0: Intel Pentium II (Deschutes) stepping 02
per-CPU timeslice cutoff: 1460.42 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/0 eip 2000
CPU 1 irqstacks, hard=c046d000 soft=c046b000
Initializing CPU#1
Calibrating delay loop... 796.67 BogoMIPS (lpj=398336)
CPU: After generic identify, caps: 0183fbff 00000000 00000000 00000000
CPU: After vendor identify, caps:  0183fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After all inits, caps:        0183fbff 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium II (Deschutes) stepping 02
Total of 2 processors activated (1583.10 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xe1285, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 20 (level, low) -> IRQ 20
ACPI: PCI interrupt 0000:00:0f.0[A] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI interrupt 0000:00:14.2[D] -> GSI 19 (level, low) -> IRQ 19
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
Starting balanced_irq
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Limiting direct PCI/PCI transfers.
inotify init: minor=63
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 440BX Chipset.
agpgart: Maximum main memory to use for agp memory: 263M
agpgart: AGP aperture is 64M @ 0x54000000
ACPI: Power Button (CM) [PBTN]
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
isapnp: Scanning for PnP cards...
isapnp: Card 'ESS ES1869 Plug and Play AudioDrive'
isapnp: 1 Plug & Play card detected total
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
e100: Intel(R) PRO/100 Network Driver, 3.0.27-k2-NAPI
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 20 (level, low) -> IRQ 20
e100: eth0: e100_probe: addr 0x50c00000, irq 20, MAC addr 00:08:C7:5C:CC:38
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: COMPAQ CR-588, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 32X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
sym53c416.c: Version 1.0.0-ac
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 21 (level, low) -> IRQ 21
sym0: <875> rev 0x4 at pci 0000:00:0b.0 irq 21
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.18j
  Vendor: HP        Model: 4.26GB B 68-5541  Rev: 5541
  Type:   Direct-Access                      ANSI SCSI revision: 02
sym0:0:0: tagged command queuing enabled, command queue depth 16.
scsi(0:0:0:0): Beginning Domain Validation
sym0:0: wide asynchronous.
sym0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 16)
scsi(0:0:0:0): Domain Validation skipping write tests
scsi(0:0:0:0): Ending Domain Validation
SCSI device sda: 8330543 512-byte hdwr sectors (4265 MB)
SCSI device sda: drive cache: write through
 /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
ip_conntrack version 2.1 (2560 buckets, 20480 max) - 304 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.  http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (ext2 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 204k freed
Adding 594396k swap on /dev/sda2.  Priority:-1 extents:1
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.


My kernel config [full config with comments at 
http://messy.desk.pl/config-2.6.9-gnetoo-r4]

CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_LOCALVERSION=""
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_SYSCTL=y
CONFIG_LOG_BUF_SHIFT=15
CONFIG_HOTPLUG=y
CONFIG_KALLSYMS=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_SHMEM=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
CONFIG_X86_PC=y
CONFIG_MPENTIUMII=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=5
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_HPET_TIMER=y
CONFIG_SMP=y
CONFIG_NR_CPUS=2
CONFIG_PREEMPT=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
CONFIG_X86_CPUID=m
CONFIG_NOHIGHMEM=y
CONFIG_MTRR=y
CONFIG_IRQBALANCE=y
CONFIG_HAVE_DEC_LOCK=y
CONFIG_PM=y
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_BLACKLIST_YEAR=0
CONFIG_ACPI_BUS=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
CONFIG_APM=y
CONFIG_APM_REAL_MODE_POWER_OFF=y
CONFIG_PCI=y
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
CONFIG_ISA=y
CONFIG_PCMCIA_PROBE=y
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_MISC=y
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_CML1=m
CONFIG_PNP=y
CONFIG_ISAPNP=y
CONFIG_BLK_DEV_FD=y
CONFIG_BLK_DEV_LOOP=m
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=y
CONFIG_IDE_TASKFILE_IO=y
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_AUTO=y
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_SG=y
CONFIG_SCSI_SPI_ATTRS=y
CONFIG_SCSI_SYM53C8XX_2=y
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
CONFIG_SCSI_QLA2XXX=y
CONFIG_SCSI_SYM53C416=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_NETFILTER=y
CONFIG_IP_NF_CONNTRACK=y
CONFIG_IP_NF_QUEUE=y
CONFIG_IP_NF_IPTABLES=y
CONFIG_IP_NF_MATCH_LIMIT=y
CONFIG_IP_NF_MATCH_IPRANGE=y
CONFIG_IP_NF_MATCH_MAC=y
CONFIG_IP_NF_MATCH_PKTTYPE=y
CONFIG_IP_NF_MATCH_MARK=y
CONFIG_IP_NF_MATCH_MULTIPORT=y
CONFIG_IP_NF_MATCH_TOS=y
CONFIG_IP_NF_MATCH_RECENT=y
CONFIG_IP_NF_MATCH_ECN=y
CONFIG_IP_NF_MATCH_DSCP=y
CONFIG_IP_NF_MATCH_AH_ESP=y
CONFIG_IP_NF_MATCH_LENGTH=y
CONFIG_IP_NF_MATCH_TTL=y
CONFIG_IP_NF_MATCH_TCPMSS=y
CONFIG_IP_NF_MATCH_HELPER=y
CONFIG_IP_NF_MATCH_STATE=y
CONFIG_IP_NF_MATCH_CONNTRACK=y
CONFIG_IP_NF_MATCH_OWNER=y
CONFIG_IP_NF_FILTER=y
CONFIG_IP_NF_TARGET_REJECT=y
CONFIG_IP_NF_TARGET_LOG=y
CONFIG_IP_NF_TARGET_ULOG=y
CONFIG_IP_NF_TARGET_TCPMSS=y
CONFIG_IP_NF_NAT=y
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=y
CONFIG_IP_NF_TARGET_REDIRECT=y
CONFIG_IP_NF_TARGET_NETMAP=y
CONFIG_IP_NF_TARGET_SAME=y
CONFIG_IP_NF_MANGLE=y
CONFIG_IP_NF_TARGET_TOS=y
CONFIG_IP_NF_TARGET_ECN=y
CONFIG_IP_NF_TARGET_DSCP=y
CONFIG_IP_NF_TARGET_MARK=y
CONFIG_IP_NF_TARGET_CLASSIFY=y
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_TARGET_NOTRACK=m
CONFIG_IP_NF_ARPTABLES=y
CONFIG_IP_NF_ARPFILTER=y
CONFIG_IP_NF_ARP_MANGLE=y
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
CONFIG_NET_PCI=y
CONFIG_E100=y
CONFIG_INPUT=y
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_INOTIFY=y
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_CORE=y
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_PRINTER=m
CONFIG_AGP=y
CONFIG_AGP_INTEL=y
CONFIG_AGP_INTEL_MCH=m
CONFIG_DRM=y
CONFIG_FB=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_VESA=m
CONFIG_FB_VESA_TNG=y
CONFIG_FB_VESA_DEFAULT_MODE="640x480@60"
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_SPEAKUP_DEFAULT="none"
CONFIG_USB=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_UHCI_HCD=m
CONFIG_USB_STORAGE=m
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_JBD=y
CONFIG_FS_MBCACHE=y
CONFIG_QUOTA=y
CONFIG_QFMT_V2=y
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
CONFIG_AUTOFS4_FS=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_UDF_FS=y
CONFIG_UDF_NLS=y
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
CONFIG_DEVFS_FS=y
CONFIG_DEVFS_MOUNT=y
CONFIG_TMPFS=y
CONFIG_RAMFS=y
CONFIG_NFS_FS=y
CONFIG_NFSD=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=y
CONFIG_EXPORTFS=y
CONFIG_SUNRPC=y
CONFIG_MSDOS_PARTITION=y
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_ISO8859_2=y
CONFIG_PROFILING=y
CONFIG_OPROFILE=y
CONFIG_EARLY_PRINTK=y
CONFIG_4KSTACKS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_PC=y


Best regards,

m.




--
gentoo-user@gentoo.org mailing list

[gentoo-user] Re: Gentoo 2004.3 hang while rebooting on Compaq ap400

[Gabriel M. Beddingfield]

Marcin Lolownik wrote:

> 
> Hello.
> 
> I have installed Gentoo 2004.3 from live cd on 2-cpu Compaq 'Professional
> Desktop AP400'.
> [dmesg's and other info attached below the post]
> When I run shutdown -r now from Live CD the system warm-reboot's without
> any problems.
> Unfortunately, when I've built a mandatory kernel, when doing shutdown the
> system goes to appropriate runlevel, unmount's disk's etc., the screen
> goes blank and the machine hangs, until i manually power it off and back
> on.

Odd.  But perhaps you're not alone.

http://www.linuxquestions.org/questions/showthread.php?threadid=200939

https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=17841

http://www.freebsd.org/cgi/query-pr.cgi?pr=27834

Only thing that looks close to a workaround is the bugzilla link where
someone says to put 'reboot=bios' in /boot/grub/grub.conf

If that doesn't work, it looks like you're chasing down a tricky bug.  Be
sure to post whatever solution you find.


-- 
                     G a b r i e l   M .   B e d d i n g f i e l d


--
gentoo-user@gentoo.org mailing list