[gentoo-user] Mythtv ATSC WinTV 1600

[Neal Hogan <nealhogan@gmail.com>]

I hope you receive the stuff below with a grain of appreciation. I've
asked for help on the mythtv forum, but have yet to get it.


I recently acquired a new Hauppauge WinTV 1600 and have successfully
gotten the analog side working with the analog channels (1-99). That
is, I can plug my (Comcast) cable from the wall to the tuner card's
analog input and get the basic cable channels.

However, the whole reason for getting tv tuner card and mythtv was to
record japanTV, which is beyond channel 99 and requires a set top box
to watch it on the TV. I've read the installation instructions for the
ATSC input of the card but I'm having problems and am aware of the IR
blaster option.

I suppose the main problem . . . the one causing the other problems
like not getting any channels is that mythtv is not "seeing" my card.
When I go to configure the capture card there is not DVB DTV card type
offered, which suggests to me that card is not being "seen."

Suggestions?

I have posted below some various info, but before that I wan to ask
one more thing, if all were fine, should it be the case that I plug
the cable from the wall to the ATSC input (i.e., not through the set
top box) and it just work (as if it were the set top box)?

Thanks for your time.
-neal

russell ~ # uname -a
Linux russell 2.6.30-gentoo-r5 #1 SMP Sun Aug 30 04:58:43 CDT 2009
i686 AMD Athlon(tm) Processor AuthenticAMD GNU/Linux


russell ~ # dmesg | grep cx18
cx18: Start initialization, version 1.2.0
cx18-0: Initializing card 0
cx18-0: Autodetected Hauppauge card
cx18 0000:00:11.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
cx18-0: Unreasonably low latency timer, setting to 64 (was 32)
cx18-0: cx23418 revision 01010000 (B)
cx18-0: Autodetected Hauppauge HVR-1600
cx18-0: Simultaneous Digital and Analog TV capture supported
IRQ 11/cx18-0: IRQF_DISABLED is not guaranteed on shared IRQs
tuner 2-0061: chip found @ 0xc2 (cx18 i2c driver #0-1)
cs5345 1-004c: chip found @ 0x98 (cx18 i2c driver #0-0)
cx18-0: Registered device video0 for encoder MPEG (64 x 32 kB)
DVB: registering new adapter (cx1
cx18-0: DVB Frontend registered
cx18-0: Registered DVB adapter0 for TS (32 x 32 kB)
cx18-0: Registered device video32 for encoder YUV (16 x 128 kB)
cx18-0: Registered device vbi0 for encoder VBI (20 x 51984 bytes)
cx18-0: Registered device video24 for encoder PCM audio (256 x 4 kB)
cx18-0: Initialized card: Hauppauge HVR-1600
cx18: End initialization
russell ~ # dmesg | grep DVB
DVB: registering new adapter (cx1
DVB: registering adapter 0 frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)...
cx18-0: DVB Frontend registered
cx18-0: Registered DVB adapter0 for TS (32 x 32 kB)

lspci -v output:
00:11.0 Multimedia video controller: Conexant CX23418 Single-Chip
MPEG-2 Encoder with Integrated Analog Video/Broadcast Audio Decoder
Subsystem: Hauppauge computer works Inc. Device 7444
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at f0000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Kernel driver in use: cx18
Kernel modules: cx18