From: michael shiloh <michael@michaelshiloh.com>
To: gentoo-user@lists.gentoo.org
Subject: Re: [gentoo-user] How can I add pcnet_cs to my installation?
Date: Sun, 5 Dec 2004 20:42:27 -0800 (PST) [thread overview]
Message-ID: <Pine.LNX.4.44.0412052035560.18836-100000@miro.michaelshiloh.com> (raw)
In-Reply-To: <20041206002904.546f7440@ulisse>
Sorry. I should have pointed that out. I am in fact using 2.6.
I actually got it all running, but I'm not sure exactly how.
I tried a kernel with no PCMCIA support, but when I emerged
pcmcia-cs it failed due to needing PCMCIA support in the kernel.
So I compiled the kernel again, this time turning on every
single PCMCIA related item I could find. This time pcmcia-cs
worked.
Some day I might redo this just to figure out what the critical
steps were, but I need to finish this installation so I can actually
use my laptop.
Still, I can see from the different answers, that there is a bit
of confusion about this issue. I appreciate all of your help as
I'll be installing Gentoo on many other computers, I'm sure.
Michael
On Mon, 6 Dec 2004, Alessandro D.M. Semeria wrote:
> Micheal not say nothing about the kernel, then I supposed he had used
> a stable gentoo-sources (2.4) and not the devel one (2.6).
>
> Best regards.
> A.S.
>
>
> On Mon, 06 Dec 2004 11:46:36 +1300
> Nick Rout <nick@rout.co.nz> wrote:
>
> > What doc are you referring to?
> >
> > AFAIK if you are on 2.6 emerge pcmcia-cs does not emerge any kernel
> > modules, but only the support programs for pcmcia.
> >
> > Thats certainly seems to be what has happenned on my laptop, which has
> > just been reinstalled with 2004.3 as of last week.
> >
> >
> > invertigating further, this is from the ebuild:
> >
> > "For 2.5/2.6 kernels, the PCMCIA support from the kernel should"
> > "be used. Enable PCMCIA and any further drivers you need there,"
> > "and then use this package to install the PCMCIA tools."
> >
> > It is otherwise for 2.4 , the ebuild says this:
> >
> > "To avail yourself of the pcmcia-cs drivers, you have to disable the"
> > "PCMCIA support in the kernel. (Otherwise, you might experience"
> > "CardServices version mismatch errors)"
> > "Proper kernel config for this package is that PCMCIA/Card Bus under"
> > "General Setup is off and Wireless LAN (non-ham radio) is on but"
> > "no modules or drivers turned on under Network Device Support"
> > "if you have wireless."
> > "Also note it now appears that you need CONFIG_CRC32 turned on"
> > "These are the CRC32 Library functions in the config"
> >
> > (sorry about the formatting)
> >
> >
> > On Sun, 5 Dec 2004 20:26:32 +0100
> > "Alessandro D.M. Semeria" <goloiat@libero.it> wrote:
> >
> > > In my personal opinion is better to emerge pcmcia modules:
> > > "emerge pcmcia-cs" (as is recommended on doc).
> > >
> > > Best regards
> > >
> > > A.S.
> > >
> > > On Sun, 05 Dec 2004 10:52:34 +1300
> > > Nick Rout <nick@rout.co.nz> wrote:
> > >
> > > > On Sun, 2004-12-05 at 10:49 +1300, Nick Rout wrote:
> > > > > you do not need to recompile the whole kernel, just the modules
> > > > > you need.
> > > > >
> > > > > in your menuconfig go into "Bus Options" and choose pcmcia
> > > > > support, with whatever options you need for your hardware.
> > > > >
> > > > > Then and only then will the right things appear under Device
> > > > > drivers/Networking Support, there will be a section for pcmcia
> > > > > drivers. Choose the NE2000 compatible one, and it will build
> > > > > pcnet_cs (according to what you read under Help anyway)
> > > >
> > > > Sorry I didn't finish :-)
> > > >
> > > > after putting the right config options in place, as modules, exit
> > > > menuconfig and execute the following
> > > >
> > > > make modules && make modules_install
> > > >
> > > > and for good measure:
> > > >
> > > > depmod -a
> > > >
> > > > it should then work without even a reboot.
> > > >
> > > > >
> > > > > On Sat, 2004-12-04 at 00:36 -0800, michael shiloh wrote:
> > > > > > Hello all,
> > > > > >
> > > > > > I'm installing Gentoo on an old laptop. After installing and
> > > > > > booting, I find that I forgot to add pcnet_cs, which I need
> > > > > > for my PCMCIA network card, so modprobe of that fails.
> > > > > >
> > > > > > Looking through the archives, I gather that this normally gets
> > > > > > built with the kernel, but I don't want to rebuild the kernel.
> > > > > > Is there a package I can emerge that will provide this?
> > > > > >
> > > > > > (I can get onto the net by booting from the live CD)
> > > > > >
> > > > > > Thanks,
> > > > > > Michael
> > > > > >
> > > > > >
> > > > > >
> > > > > > --
> > > > > > gentoo-user@gentoo.org mailing list
> > > > > >
> > > > --
> > > > Nick Rout <nick@rout.co.nz>
> > > >
> > > >
> > > > --
> > > > gentoo-user@gentoo.org mailing list
> > > >
> > >
> > > --
> > > gentoo-user@gentoo.org mailing list
> >
> > --
> > Nick Rout <nick@rout.co.nz>
> >
> >
> > --
> > gentoo-user@gentoo.org mailing list
> >
>
> --
> gentoo-user@gentoo.org mailing list
>
--
gentoo-user@gentoo.org mailing list
next prev parent reply other threads:[~2004-12-06 4:57 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <Pine.LNX.4.44.0412040035570.18836-100000@miro.michaelshiloh.com>
2004-12-04 21:49 ` [gentoo-user] How can I add pcnet_cs to my installation? Nick Rout
2004-12-04 21:52 ` Nick Rout
2004-12-05 19:26 ` Alessandro D.M. Semeria
2004-12-05 22:46 ` Nick Rout
2004-12-05 23:29 ` Alessandro D.M. Semeria
2004-12-06 0:05 ` Nick Rout
2004-12-06 4:42 ` michael shiloh [this message]
2004-12-06 8:42 ` Nick Rout
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Pine.LNX.4.44.0412052035560.18836-100000@miro.michaelshiloh.com \
--to=michael@michaelshiloh.com \
--cc=gentoo-user@lists.gentoo.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox