* [gentoo-user] video capture
@ 2006-07-15 13:12 99% rob
0 siblings, 0 replies; 1+ results
From: rob @ 2006-07-15 13:12 UTC (permalink / raw
To: gentoo-user
I just bought a hauppauge winTV-PVR-150
kernel linux-2.6.16-gentoo-r12
I compiled all the stuff for the bttv driver
CONFIG_VIDEO_BT848=y
CONFIG_VIDEO_BT848_DVB=y
CONFIG_VIDEO_SAA6588=y
CONFIG_VIDEO_CX88_VP3054=y
CONFIG_VIDEO_AUDIO_DECODER=y
CONFIG_VIDEO_DECODER=y
CONFIG_DVB=y
CONFIG_DVB_CORE=y
CONFIG_DVB_BT8XX=y
CONFIG_DVB_SP887X=y
CONFIG_DVB_CX22700=y
CONFIG_DVB_TDA1004X=y
CONFIG_DVB_NXT6000=y
CONFIG_DVB_MT352=y
kernel sees the card
Jul 15 07:25:44 localhost bttv: driver version 0.9.16 loaded
Jul 15 07:25:44 localhost bttv: using 8 buffers with 2080k (520 pages) each
for capture
Jul 15 07:25:44 localhost bt878: AUDIO driver version 0.0.0 loaded
even tryed ivtv
Jul 15 07:25:44 localhost ivtv: ==================== START INIT IVTV
====================
Jul 15 07:25:44 localhost ivtv: version 0.6.3 (tagged release) loading
Jul 15 07:25:44 localhost ivtv: Linux version: 2.6.16-gentoo-r12 SMP preempt
PENTIUM4 gcc-3.4
Jul 15 07:25:44 localhost ivtv: In case of problems please include the debug
info between
Jul 15 07:25:44 localhost ivtv: the START INIT IVTV and END INIT IVTV lines,
along with
Jul 15 07:25:44 localhost ivtv: any module options, when mailing the
ivtv-users mailinglist.
Jul 15 07:25:44 localhost ivtv0: Autodetected Hauppauge WinTV PVR-150 card
(cx23416 based)
Jul 15 07:25:44 localhost ivtv0: Unreasonably low latency timer, setting to 64
(was 32)
Jul 15 07:25:44 localhost wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver
#0)
Jul 15 07:25:44 localhost tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
Jul 15 07:25:44 localhost cx25840 0-0044: cx25841-23 found @ 0x88 (ivtv i2c
driver #0)
Jul 15 07:25:44 localhost cx25840 0-0044: loaded v4l-cx25840.fw firmware
(14264 bytes)
Jul 15 07:25:44 localhost tveeprom 0-0050: Hauppauge model 26132, rev G1B2,
serial# 9543549
Jul 15 07:25:44 localhost tveeprom 0-0050: tuner model is TCL M2523_5N_E (idx
112, type 4)
Jul 15 07:25:44 localhost tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
Jul 15 07:25:44 localhost tveeprom 0-0050: audio processor is CX25841 (idx 35)
Jul 15 07:25:44 localhost tveeprom 0-0050: decoder processor is CX25841 (idx
28)
Jul 15 07:25:44 localhost tveeprom 0-0050: has no radio, has IR remote
Jul 15 07:25:44 localhost ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144
bytes)
Jul 15 07:25:44 localhost ivtv0: Encoder revision: 0x02050032
Jul 15 07:25:44 localhost ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768
buffers (4096KB total)
Jul 15 07:25:44 localhost ivtv0: Allocate DMA encoder YUV stream: 194 x 10800
buffers (2048KB total)
Jul 15 07:25:44 localhost ivtv0: Allocate DMA encoder VBI stream: 120 x 17472
buffers (2048KB total)
Jul 15 07:25:44 localhost ivtv0: Allocate DMA encoder PCM audio stream: 455 x
4608 buffers (2048KB total)
Jul 15 07:25:44 localhost tuner 0-0061: tuner type not set
Jul 15 07:25:44 localhost tuner 0-0061: tuner type not set
Jul 15 07:25:44 localhost ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
Jul 15 07:25:44 localhost ivtv: ==================== END INIT IVTV
====================
emerged most of the stuff in media-tv but I can't get anyone of thease to
show TV most say device not configured. Evan the ones that I know point
to /dev/video0
I think I did everything right.
pleas help or tell me of a better card to use.
rob
--
gentoo-user@gentoo.org mailing list
^ permalink raw reply [relevance 99%]
Results 1-1 of 1 | reverse | options above
-- pct% links below jump to the message on this page, permalinks otherwise --
2006-07-15 13:12 99% [gentoo-user] video capture rob
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox