[gentoo-user] Having Trouble with Wireless Interface

[gentoo-user] Having Trouble with Wireless Interface

[Hunter Jozwiak]

Hi all. I got Espeakup to finally function, but I have a problem now
with my Realtech 8188 WiFi adapter, Rev01, according to ifconfig. I
know it shows up as wlp7s0 on an ifconfig, normally. But for what ever
reason, it isn't showing up. I have, in my /etc/conf.d/net the line:
wlp7s0="DHCP". When I run ifconfig wlp7s0 up, I get an error about how
the device is not able to be found. The driver shows up as a module in
the kernel.

Re: [gentoo-user] Having Trouble with Wireless Interface

[the]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA256

On 05/12/14 23:31, Hunter Jozwiak wrote:
> Hi all. I got Espeakup to finally function, but I have a problem
> now with my Realtech 8188 WiFi adapter, Rev01, according to
> ifconfig. I know it shows up as wlp7s0 on an ifconfig, normally.
> But for what ever reason, it isn't showing up. I have, in my
> /etc/conf.d/net the line: wlp7s0="DHCP". When I run ifconfig wlp7s0
> up, I get an error about how the device is not able to be found.
> The driver shows up as a module in the kernel.
Could it be a firmware problem? dmesg would help.

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/

iQEcBAEBCAAGBQJTca6DAAoJEK64IL1uI2haJ1sIAJfCcqmesAcByVMGt6gn3+jD
5J6equcfr5/2xh+qJ7WmVR3RYtZTqeoBhfhUEvLcDRhuA5HgXg5owgIQBjynEfdw
91SEXM00bJ+2y4JPh31aYMGnLx279B+OMw13dOYzZmwOSHU1DK4AiJW/ueYSb8LS
XVI8tJJS+D3XY4lbdiWNykc9nEhbgI4IahNFS8bZP9wuf3OFtBGo6zJn/sAN3EEg
FLArhZpnncmdeQI07exHpMsqRY380MUPgua3acygVjKfkrIzKhwzsKRoWYj5IZqd
3Emzcoc6+xQgQl65EborNOrvsgwEN/3ZW2MClNnLq2m4kuqaY6GnPEacGowxwbo=
=O1JI
-----END PGP SIGNATURE-----

Re: [gentoo-user] Having Trouble with Wireless Interface

[Alexander Kapshuk]

On 05/12/2014 10:31 PM, Hunter Jozwiak wrote:
> Hi all. I got Espeakup to finally function, but I have a problem now
> with my Realtech 8188 WiFi adapter, Rev01, according to ifconfig. I
> know it shows up as wlp7s0 on an ifconfig, normally. But for what ever
> reason, it isn't showing up. I have, in my /etc/conf.d/net the line:
> wlp7s0="DHCP". When I run ifconfig wlp7s0 up, I get an error about how
> the device is not able to be found. The driver shows up as a module in
> the kernel.
>
I use wpa_supplicant to manage my wireless connections.
Here's what I have in my /etc/conf.d/net:
# Prefer wpa_supplicant over wireless-tools
modules="wpa_supplicant"

wpa_supplicant_wlp2s0="-Dnl80211"

And the output of lspci:
02:00.0 Ethernet controller: Qualcomm Atheros AR242x / AR542x Wireless
Network Adapter (PCI-Express) (rev 01)
    Subsystem: Hewlett-Packard Company Device 137b
    Flags: bus master, fast devsel, latency 0, IRQ 16
    Memory at d6000000 (64-bit, non-prefetchable) [size=64K]
    Capabilities: [40] Power Management version 2
    Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
    Capabilities: [60] Express Legacy Endpoint, MSI 00
    Capabilities: [90] MSI-X: Enable- Count=1 Masked-
    Capabilities: [100] Advanced Error Reporting
    Capabilities: [140] Virtual Channel
    Kernel driver in use: ath5k
    Kernel modules: ath5k

Are you setting up wireless after doing a fresh install, or did you have
it working before and then it just stopped working for you?

RE: [gentoo-user] Having Trouble with Wireless Interface

[Hunter Jozwiak]

-----Original Message-----
From: Alexander Kapshuk [mailto:alexander.kapshuk@gmail.com] 
Sent: Tuesday, May 13, 2014 7:00 AM
To: gentoo-user@lists.gentoo.org
Subject: Re: [gentoo-user] Having Trouble with Wireless Interface

On 05/12/2014 10:31 PM, Hunter Jozwiak wrote:
> Hi all. I got Espeakup to finally function, but I have a problem now 
> with my Realtech 8188 WiFi adapter, Rev01, according to ifconfig. I 
> know it shows up as wlp7s0 on an ifconfig, normally. But for what ever 
> reason, it isn't showing up. I have, in my /etc/conf.d/net the line:
> wlp7s0="DHCP". When I run ifconfig wlp7s0 up, I get an error about how 
> the device is not able to be found. The driver shows up as a module in 
> the kernel.
>
I use wpa_supplicant to manage my wireless connections.
Here's what I have in my /etc/conf.d/net:
# Prefer wpa_supplicant over wireless-tools modules="wpa_supplicant"

wpa_supplicant_wlp2s0="-Dnl80211"

And the output of lspci:
02:00.0 Ethernet controller: Qualcomm Atheros AR242x / AR542x Wireless
Network Adapter (PCI-Express) (rev 01)
    Subsystem: Hewlett-Packard Company Device 137b
    Flags: bus master, fast devsel, latency 0, IRQ 16
    Memory at d6000000 (64-bit, non-prefetchable) [size=64K]
    Capabilities: [40] Power Management version 2
    Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
    Capabilities: [60] Express Legacy Endpoint, MSI 00
    Capabilities: [90] MSI-X: Enable- Count=1 Masked-
    Capabilities: [100] Advanced Error Reporting
    Capabilities: [140] Virtual Channel
    Kernel driver in use: ath5k
    Kernel modules: ath5k

Are you setting up wireless after doing a fresh install, or did you have it
working before and then it just stopped working for you?

This is fresh. And genkernel doesn't show RTL8188CE in the staging drivers.
It shows drivers with uffixes U and Eu, but not the CE driver.

Re: [gentoo-user] Having Trouble with Wireless Interface

[Alexander Kapshuk]

On 05/13/2014 02:45 PM, Hunter Jozwiak wrote:
>
> -----Original Message-----
> From: Alexander Kapshuk [mailto:alexander.kapshuk@gmail.com] 
> Sent: Tuesday, May 13, 2014 7:00 AM
> To: gentoo-user@lists.gentoo.org
> Subject: Re: [gentoo-user] Having Trouble with Wireless Interface
>
> On 05/12/2014 10:31 PM, Hunter Jozwiak wrote:
>> Hi all. I got Espeakup to finally function, but I have a problem now 
>> with my Realtech 8188 WiFi adapter, Rev01, according to ifconfig. I 
>> know it shows up as wlp7s0 on an ifconfig, normally. But for what ever 
>> reason, it isn't showing up. I have, in my /etc/conf.d/net the line:
>> wlp7s0="DHCP". When I run ifconfig wlp7s0 up, I get an error about how 
>> the device is not able to be found. The driver shows up as a module in 
>> the kernel.
>>
> I use wpa_supplicant to manage my wireless connections.
> Here's what I have in my /etc/conf.d/net:
> # Prefer wpa_supplicant over wireless-tools modules="wpa_supplicant"
>
> wpa_supplicant_wlp2s0="-Dnl80211"
>
> And the output of lspci:
> 02:00.0 Ethernet controller: Qualcomm Atheros AR242x / AR542x Wireless
> Network Adapter (PCI-Express) (rev 01)
>     Subsystem: Hewlett-Packard Company Device 137b
>     Flags: bus master, fast devsel, latency 0, IRQ 16
>     Memory at d6000000 (64-bit, non-prefetchable) [size=64K]
>     Capabilities: [40] Power Management version 2
>     Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
>     Capabilities: [60] Express Legacy Endpoint, MSI 00
>     Capabilities: [90] MSI-X: Enable- Count=1 Masked-
>     Capabilities: [100] Advanced Error Reporting
>     Capabilities: [140] Virtual Channel
>     Kernel driver in use: ath5k
>     Kernel modules: ath5k
>
> Are you setting up wireless after doing a fresh install, or did you have it
> working before and then it just stopped working for you?
>
> This is fresh. And genkernel doesn't show RTL8188CE in the staging drivers.
> It shows drivers with uffixes U and Eu, but not the CE driver.
>
>
Looks like the kernel driver for your wireless NIC is RTL8192CE
---------------------------------------------------------------------
/usr/src/linux/drivers/net/wireless/rtlwifi/Kconfig:12,22
config RTL8192CE
    tristate "Realtek RTL8192CE/RTL8188CE Wireless Network Adapter"
    depends on PCI
    select RTL8192C_COMMON
    select RTLWIFI
    select RTLWIFI_PCI
    ---help---
    This is the driver for Realtek RTL8192CE/RTL8188CE 802.11n PCIe
    wireless network adapters.

    If you choose to build it as a module, it will be called rtl8192ce
---------------------------------------------------------------------
If you like to check if RTL8192CE is enabled in  your kernel's .config
file. If it isn't, you probably want to compile it as a module, and then
add rtl8192ce to /etc/conf.d/modules as well.

RE: [gentoo-user] Having Trouble with Wireless Interface

[Hunter Jozwiak]

-----Original Message-----
From: Alexander Kapshuk [mailto:alexander.kapshuk@gmail.com] 
Sent: Tuesday, May 13, 2014 8:20 AM
To: gentoo-user@lists.gentoo.org
Subject: Re: [gentoo-user] Having Trouble with Wireless Interface

On 05/13/2014 02:45 PM, Hunter Jozwiak wrote:
>
> -----Original Message-----
> From: Alexander Kapshuk [mailto:alexander.kapshuk@gmail.com]
> Sent: Tuesday, May 13, 2014 7:00 AM
> To: gentoo-user@lists.gentoo.org
> Subject: Re: [gentoo-user] Having Trouble with Wireless Interface
>
> On 05/12/2014 10:31 PM, Hunter Jozwiak wrote:
>> Hi all. I got Espeakup to finally function, but I have a problem now 
>> with my Realtech 8188 WiFi adapter, Rev01, according to ifconfig. I 
>> know it shows up as wlp7s0 on an ifconfig, normally. But for what 
>> ever reason, it isn't showing up. I have, in my /etc/conf.d/net the line:
>> wlp7s0="DHCP". When I run ifconfig wlp7s0 up, I get an error about 
>> how the device is not able to be found. The driver shows up as a 
>> module in the kernel.
>>
> I use wpa_supplicant to manage my wireless connections.
> Here's what I have in my /etc/conf.d/net:
> # Prefer wpa_supplicant over wireless-tools modules="wpa_supplicant"
>
> wpa_supplicant_wlp2s0="-Dnl80211"
>
> And the output of lspci:
> 02:00.0 Ethernet controller: Qualcomm Atheros AR242x / AR542x Wireless 
> Network Adapter (PCI-Express) (rev 01)
>     Subsystem: Hewlett-Packard Company Device 137b
>     Flags: bus master, fast devsel, latency 0, IRQ 16
>     Memory at d6000000 (64-bit, non-prefetchable) [size=64K]
>     Capabilities: [40] Power Management version 2
>     Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
>     Capabilities: [60] Express Legacy Endpoint, MSI 00
>     Capabilities: [90] MSI-X: Enable- Count=1 Masked-
>     Capabilities: [100] Advanced Error Reporting
>     Capabilities: [140] Virtual Channel
>     Kernel driver in use: ath5k
>     Kernel modules: ath5k
>
> Are you setting up wireless after doing a fresh install, or did you 
> have it working before and then it just stopped working for you?
>
> This is fresh. And genkernel doesn't show RTL8188CE in the staging
drivers.
> It shows drivers with uffixes U and Eu, but not the CE driver.
>
>
Looks like the kernel driver for your wireless NIC is RTL8192CE
---------------------------------------------------------------------
/usr/src/linux/drivers/net/wireless/rtlwifi/Kconfig:12,22
config RTL8192CE
    tristate "Realtek RTL8192CE/RTL8188CE Wireless Network Adapter"
    depends on PCI
    select RTL8192C_COMMON
    select RTLWIFI
    select RTLWIFI_PCI
    ---help---
    This is the driver for Realtek RTL8192CE/RTL8188CE 802.11n PCIe
    wireless network adapters.

    If you choose to build it as a module, it will be called rtl8192ce
---------------------------------------------------------------------
If you like to check if RTL8192CE is enabled in  your kernel's .config file.
If it isn't, you probably want to compile it as a module, and then add
rtl8192ce to /etc/conf.d/modules as well.

Oddly enough, I had a few other CONFIG modules not included, namely
CONFIG_80211. But, when I activated it, my kernel got bricked, and on
reboot, I got dumped in some prompt that said that the system couldn't find
a root and I should press Enter to continue, Q to skip, and something else
would give me a shell. I just did a genkernel --menuconfig kernel and built
in the modules, the compile went smooth, and I made no other changes. But
now, like I've mentioned, I've got a bricked kernel.

Re: [gentoo-user] Having Trouble with Wireless Interface

[Alexander Kapshuk]

On 05/13/2014 04:25 PM, Hunter Jozwiak wrote:
>
> -----Original Message-----
> From: Alexander Kapshuk [mailto:alexander.kapshuk@gmail.com] 
> Sent: Tuesday, May 13, 2014 8:20 AM
> To: gentoo-user@lists.gentoo.org
> Subject: Re: [gentoo-user] Having Trouble with Wireless Interface
>
> On 05/13/2014 02:45 PM, Hunter Jozwiak wrote:
>> -----Original Message-----
>> From: Alexander Kapshuk [mailto:alexander.kapshuk@gmail.com]
>> Sent: Tuesday, May 13, 2014 7:00 AM
>> To: gentoo-user@lists.gentoo.org
>> Subject: Re: [gentoo-user] Having Trouble with Wireless Interface
>>
>> On 05/12/2014 10:31 PM, Hunter Jozwiak wrote:
>>> Hi all. I got Espeakup to finally function, but I have a problem now 
>>> with my Realtech 8188 WiFi adapter, Rev01, according to ifconfig. I 
>>> know it shows up as wlp7s0 on an ifconfig, normally. But for what 
>>> ever reason, it isn't showing up. I have, in my /etc/conf.d/net the line:
>>> wlp7s0="DHCP". When I run ifconfig wlp7s0 up, I get an error about 
>>> how the device is not able to be found. The driver shows up as a 
>>> module in the kernel.
>>>
>> I use wpa_supplicant to manage my wireless connections.
>> Here's what I have in my /etc/conf.d/net:
>> # Prefer wpa_supplicant over wireless-tools modules="wpa_supplicant"
>>
>> wpa_supplicant_wlp2s0="-Dnl80211"
>>
>> And the output of lspci:
>> 02:00.0 Ethernet controller: Qualcomm Atheros AR242x / AR542x Wireless 
>> Network Adapter (PCI-Express) (rev 01)
>>     Subsystem: Hewlett-Packard Company Device 137b
>>     Flags: bus master, fast devsel, latency 0, IRQ 16
>>     Memory at d6000000 (64-bit, non-prefetchable) [size=64K]
>>     Capabilities: [40] Power Management version 2
>>     Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
>>     Capabilities: [60] Express Legacy Endpoint, MSI 00
>>     Capabilities: [90] MSI-X: Enable- Count=1 Masked-
>>     Capabilities: [100] Advanced Error Reporting
>>     Capabilities: [140] Virtual Channel
>>     Kernel driver in use: ath5k
>>     Kernel modules: ath5k
>>
>> Are you setting up wireless after doing a fresh install, or did you 
>> have it working before and then it just stopped working for you?
>>
>> This is fresh. And genkernel doesn't show RTL8188CE in the staging
> drivers.
>> It shows drivers with uffixes U and Eu, but not the CE driver.
>>
>>
> Looks like the kernel driver for your wireless NIC is RTL8192CE
> ---------------------------------------------------------------------
> /usr/src/linux/drivers/net/wireless/rtlwifi/Kconfig:12,22
> config RTL8192CE
>     tristate "Realtek RTL8192CE/RTL8188CE Wireless Network Adapter"
>     depends on PCI
>     select RTL8192C_COMMON
>     select RTLWIFI
>     select RTLWIFI_PCI
>     ---help---
>     This is the driver for Realtek RTL8192CE/RTL8188CE 802.11n PCIe
>     wireless network adapters.
>
>     If you choose to build it as a module, it will be called rtl8192ce
> ---------------------------------------------------------------------
> If you like to check if RTL8192CE is enabled in  your kernel's .config file.
> If it isn't, you probably want to compile it as a module, and then add
> rtl8192ce to /etc/conf.d/modules as well.
>
> Oddly enough, I had a few other CONFIG modules not included, namely
> CONFIG_80211. But, when I activated it, my kernel got bricked, and on
> reboot, I got dumped in some prompt that said that the system couldn't find
> a root and I should press Enter to continue, Q to skip, and something else
> would give me a shell. I just did a genkernel --menuconfig kernel and built
> in the modules, the compile went smooth, and I made no other changes. But
> now, like I've mentioned, I've got a bricked kernel.
>
>
Did your genkernel boot OK, before you enabled 'CONFIG_.*80211'?
What output does the command line shown below return?
grep '^CONFIG.*80211.*=[nmy]' /usr/src/linux/.config
Here's what I get on my system:
CONFIG_CFG80211=y
CONFIG_CFG80211_DEFAULT_PS=y
CONFIG_MAC80211=y
CONFIG_MAC80211_HAS_RC=y
CONFIG_MAC80211_RC_MINSTREL=y
CONFIG_MAC80211_RC_MINSTREL_HT=y
CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
CONFIG_MAC80211_LEDS=y

I assume you also ran 'genkernel all' after running 'genkernel
--menuconfig', didn't you?

What's the contents of your /etc/conf.d/modules?

/etc/fstab?

and what's the output of 'mount|grep ^/dev'?

Re: [gentoo-user] Having Trouble with Wireless Interface

[Alexander Kapshuk]

On 05/13/2014 04:53 PM, Alexander Kapshuk wrote:
> On 05/13/2014 04:25 PM, Hunter Jozwiak wrote:
>> -----Original Message-----
>> From: Alexander Kapshuk [mailto:alexander.kapshuk@gmail.com] 
>> Sent: Tuesday, May 13, 2014 8:20 AM
>> To: gentoo-user@lists.gentoo.org
>> Subject: Re: [gentoo-user] Having Trouble with Wireless Interface
>>
>> On 05/13/2014 02:45 PM, Hunter Jozwiak wrote:
>>> -----Original Message-----
>>> From: Alexander Kapshuk [mailto:alexander.kapshuk@gmail.com]
>>> Sent: Tuesday, May 13, 2014 7:00 AM
>>> To: gentoo-user@lists.gentoo.org
>>> Subject: Re: [gentoo-user] Having Trouble with Wireless Interface
>>>
>>> On 05/12/2014 10:31 PM, Hunter Jozwiak wrote:
>>>> Hi all. I got Espeakup to finally function, but I have a problem now 
>>>> with my Realtech 8188 WiFi adapter, Rev01, according to ifconfig. I 
>>>> know it shows up as wlp7s0 on an ifconfig, normally. But for what 
>>>> ever reason, it isn't showing up. I have, in my /etc/conf.d/net the line:
>>>> wlp7s0="DHCP". When I run ifconfig wlp7s0 up, I get an error about 
>>>> how the device is not able to be found. The driver shows up as a 
>>>> module in the kernel.
>>>>
>>> I use wpa_supplicant to manage my wireless connections.
>>> Here's what I have in my /etc/conf.d/net:
>>> # Prefer wpa_supplicant over wireless-tools modules="wpa_supplicant"
>>>
>>> wpa_supplicant_wlp2s0="-Dnl80211"
>>>
>>> And the output of lspci:
>>> 02:00.0 Ethernet controller: Qualcomm Atheros AR242x / AR542x Wireless 
>>> Network Adapter (PCI-Express) (rev 01)
>>>     Subsystem: Hewlett-Packard Company Device 137b
>>>     Flags: bus master, fast devsel, latency 0, IRQ 16
>>>     Memory at d6000000 (64-bit, non-prefetchable) [size=64K]
>>>     Capabilities: [40] Power Management version 2
>>>     Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
>>>     Capabilities: [60] Express Legacy Endpoint, MSI 00
>>>     Capabilities: [90] MSI-X: Enable- Count=1 Masked-
>>>     Capabilities: [100] Advanced Error Reporting
>>>     Capabilities: [140] Virtual Channel
>>>     Kernel driver in use: ath5k
>>>     Kernel modules: ath5k
>>>
>>> Are you setting up wireless after doing a fresh install, or did you 
>>> have it working before and then it just stopped working for you?
>>>
>>> This is fresh. And genkernel doesn't show RTL8188CE in the staging
>> drivers.
>>> It shows drivers with uffixes U and Eu, but not the CE driver.
>>>
>>>
>> Looks like the kernel driver for your wireless NIC is RTL8192CE
>> ---------------------------------------------------------------------
>> /usr/src/linux/drivers/net/wireless/rtlwifi/Kconfig:12,22
>> config RTL8192CE
>>     tristate "Realtek RTL8192CE/RTL8188CE Wireless Network Adapter"
>>     depends on PCI
>>     select RTL8192C_COMMON
>>     select RTLWIFI
>>     select RTLWIFI_PCI
>>     ---help---
>>     This is the driver for Realtek RTL8192CE/RTL8188CE 802.11n PCIe
>>     wireless network adapters.
>>
>>     If you choose to build it as a module, it will be called rtl8192ce
>> ---------------------------------------------------------------------
>> If you like to check if RTL8192CE is enabled in  your kernel's .config file.
>> If it isn't, you probably want to compile it as a module, and then add
>> rtl8192ce to /etc/conf.d/modules as well.
>>
>> Oddly enough, I had a few other CONFIG modules not included, namely
>> CONFIG_80211. But, when I activated it, my kernel got bricked, and on
>> reboot, I got dumped in some prompt that said that the system couldn't find
>> a root and I should press Enter to continue, Q to skip, and something else
>> would give me a shell. I just did a genkernel --menuconfig kernel and built
>> in the modules, the compile went smooth, and I made no other changes. But
>> now, like I've mentioned, I've got a bricked kernel.
>>
>>
> Did your genkernel boot OK, before you enabled 'CONFIG_.*80211'?
> What output does the command line shown below return?
> grep '^CONFIG.*80211.*=[nmy]' /usr/src/linux/.config
> Here's what I get on my system:
> CONFIG_CFG80211=y
> CONFIG_CFG80211_DEFAULT_PS=y
> CONFIG_MAC80211=y
> CONFIG_MAC80211_HAS_RC=y
> CONFIG_MAC80211_RC_MINSTREL=y
> CONFIG_MAC80211_RC_MINSTREL_HT=y
> CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
> CONFIG_MAC80211_LEDS=y
>
> I assume you also ran 'genkernel all' after running 'genkernel
> --menuconfig', didn't you?
>
> What's the contents of your /etc/conf.d/modules?
>
> /etc/fstab?
>
> and what's the output of 'mount|grep ^/dev'?
>
>
While I do not use genkernel myself, I thought you might want to take a
look at this wiki article, http://wiki.gentoo.org/wiki/Genkernel, as a
way to retrace your steps and hopefully find what's got amiss.

Re: [gentoo-user] Having Trouble with Wireless Interface

[Stroller]

On Tue, 13 May 2014, at 1:19 pm, Alexander Kapshuk <alexander.kapshuk@gmail.com> wrote:
> … 
> If you like to check if RTL8192CE is enabled in  your kernel's .config
> file. If it isn't, you probably want to compile it as a module, and then
> add rtl8192ce to /etc/conf.d/modules as well.

Am pretty sure there's no need to add this one to /etc/conf.d/modules - IME it'll just be found and loaded automagically by the kernel.

Stroller.

Re: [gentoo-user] Having Trouble with Wireless Interface

[Alexander Kapshuk]

On 05/14/2014 12:41 PM, Stroller wrote:
> On Tue, 13 May 2014, at 1:19 pm, Alexander Kapshuk <alexander.kapshuk@gmail.com> wrote:
>> … 
>> If you like to check if RTL8192CE is enabled in  your kernel's .config
>> file. If it isn't, you probably want to compile it as a module, and then
>> add rtl8192ce to /etc/conf.d/modules as well.
> Am pretty sure there's no need to add this one to /etc/conf.d/modules - IME it'll just be found and loaded automagically by the kernel.
>
> Stroller.
>
>
Thanks for pointing that out. I wasn't aware of that. As I mentioned in
my previous post, I do not use genkernel myself. That's why I thought
I'd refer the person inquiring to the gentoo wiki article about genkernel.

Hopefully, someone else on this list with more experience building the
genkernel will be able to offer advice that would be helpful.

Re: [gentoo-user] Having Trouble with Wireless Interface

[Stroller]

On Wed, 14 May 2014, at 12:36 pm, Alexander Kapshuk <alexander.kapshuk@gmail.com> wrote:
>>> … 
>>> If you like to check if RTL8192CE is enabled in  your kernel's .config
>>> file. If it isn't, you probably want to compile it as a module, and then
>>> add rtl8192ce to /etc/conf.d/modules as well.
>> Am pretty sure there's no need to add this one to /etc/conf.d/modules - IME it'll just be found and loaded automagically by the kernel.
> 
> Thanks for pointing that out. I wasn't aware of that. As I mentioned in
> my previous post, I do not use genkernel myself.

Neither do I - for this reason I found it a little frustrating trying to help in a recent thread, myself.

However, I'm pretty sure that loadable kernel modules behave the same whether your kernel is built "by hand" or by genkernel - if you have modules listed in /etc/conf.d/modules then I have to wonder if you really need them there.

I haven't used that file for years, and I prefer to compile everything as a module, too.

Stroller.

Re: [gentoo-user] Having Trouble with Wireless Interface

[Alan McKinnon]

On 15/05/2014 10:39, Stroller wrote:
> 
> On Wed, 14 May 2014, at 12:36 pm, Alexander Kapshuk <alexander.kapshuk@gmail.com> wrote:
>>>> … 
>>>> If you like to check if RTL8192CE is enabled in  your kernel's .config
>>>> file. If it isn't, you probably want to compile it as a module, and then
>>>> add rtl8192ce to /etc/conf.d/modules as well.
>>> Am pretty sure there's no need to add this one to /etc/conf.d/modules - IME it'll just be found and loaded automagically by the kernel.
>>
>> Thanks for pointing that out. I wasn't aware of that. As I mentioned in
>> my previous post, I do not use genkernel myself.
> 
> Neither do I - for this reason I found it a little frustrating trying to help in a recent thread, myself.
> 
> However, I'm pretty sure that loadable kernel modules behave the same whether your kernel is built "by hand" or by genkernel - if you have modules listed in /etc/conf.d/modules then I have to wonder if you really need them there.
> 
> I haven't used that file for years, and I prefer to compile everything as a module, too.


Some modules don't autoload, usually because there's no hardware they
drive and so nothing to probe.

netfilter modules come to mind, as well as VirtualBox. One of the vbox
modules doesn't autoload by just stating VirtualBox, so the easiest is
to put it in /etc/conf.d/modules so it's always available. It's an edge
case, so the vast majority of modules load properly without intervention
form us.




-- 
Alan McKinnon
alan.mckinnon@gmail.com

RE: [gentoo-user] Having Trouble with Wireless Interface

[Hunter Jozwiak]

I got the networking interface to function correct.y now. Thanks all for the
help!

-----Original Message-----
From: Alan McKinnon [mailto:alan.mckinnon@gmail.com] 
Sent: Thursday, May 15, 2014 5:29 AM
To: gentoo-user@lists.gentoo.org
Subject: Re: [gentoo-user] Having Trouble with Wireless Interface

On 15/05/2014 10:39, Stroller wrote:
> 
> On Wed, 14 May 2014, at 12:36 pm, Alexander Kapshuk
<alexander.kapshuk@gmail.com> wrote:
>>>> .
>>>> If you like to check if RTL8192CE is enabled in  your kernel's 
>>>> .config file. If it isn't, you probably want to compile it as a 
>>>> module, and then add rtl8192ce to /etc/conf.d/modules as well.
>>> Am pretty sure there's no need to add this one to /etc/conf.d/modules -
IME it'll just be found and loaded automagically by the kernel.
>>
>> Thanks for pointing that out. I wasn't aware of that. As I mentioned 
>> in my previous post, I do not use genkernel myself.
> 
> Neither do I - for this reason I found it a little frustrating trying to
help in a recent thread, myself.
> 
> However, I'm pretty sure that loadable kernel modules behave the same
whether your kernel is built "by hand" or by genkernel - if you have modules
listed in /etc/conf.d/modules then I have to wonder if you really need them
there.
> 
> I haven't used that file for years, and I prefer to compile everything as
a module, too.


Some modules don't autoload, usually because there's no hardware they drive
and so nothing to probe.

netfilter modules come to mind, as well as VirtualBox. One of the vbox
modules doesn't autoload by just stating VirtualBox, so the easiest is to
put it in /etc/conf.d/modules so it's always available. It's an edge case,
so the vast majority of modules load properly without intervention form us.




--
Alan McKinnon
alan.mckinnon@gmail.com

Re: [gentoo-user] Having Trouble with Wireless Interface

[Stroller]

On Thu, 15 May 2014, at 10:29 am, Alan McKinnon <alan.mckinnon@gmail.com> wrote:
>> … 
>> However, I'm pretty sure that loadable kernel modules behave the same whether your kernel is built "by hand" or by genkernel - if you have modules listed in /etc/conf.d/modules then I have to wonder if you really need them there.
>> 
>> I haven't used that file for years, and I prefer to compile everything as a module, too.
> 
> Some modules don't autoload, usually because there's no hardware they
> drive and so nothing to probe.
> 
> netfilter modules come to mind, as well as VirtualBox. … 

Many thanks, that's very informative.

Stroller.

Re: [gentoo-user] Having Trouble with Wireless Interface

[Alexander Kapshuk]

On 05/15/2014 11:39 AM, Stroller wrote:
> On Wed, 14 May 2014, at 12:36 pm, Alexander Kapshuk <alexander.kapshuk@gmail.com> wrote:
>>>> … 
>>>> If you like to check if RTL8192CE is enabled in  your kernel's .config
>>>> file. If it isn't, you probably want to compile it as a module, and then
>>>> add rtl8192ce to /etc/conf.d/modules as well.
>>> Am pretty sure there's no need to add this one to /etc/conf.d/modules - IME it'll just be found and loaded automagically by the kernel.
>> Thanks for pointing that out. I wasn't aware of that. As I mentioned in
>> my previous post, I do not use genkernel myself.
> Neither do I - for this reason I found it a little frustrating trying to help in a recent thread, myself.
>
> However, I'm pretty sure that loadable kernel modules behave the same whether your kernel is built "by hand" or by genkernel - if you have modules listed in /etc/conf.d/modules then I have to wonder if you really need them there.
>
> I haven't used that file for years, and I prefer to compile everything as a module, too.
>
> Stroller.
>
>
That's interesting. I wasn't aware of that either.

So far, I've just been following the instructions given in the handbook,
section 7.d, which do recommend explicitly specifying the kernel modules
to be loaded at boot time in /etc/conf.d/modules.

How does the kernel know then what modules to load at boot time, if it
doesn't rely on /etc/conf.d/modules to supply the list of modules to be
loaded?

Does it use udev, or some other mechanism for that?

Thanks.

Re: [gentoo-user] Having Trouble with Wireless Interface

[Mick]

[-- Attachment #1: Type: Text/Plain, Size: 2014 bytes --]

On Thursday 15 May 2014 14:24:57 Alexander Kapshuk wrote:
> On 05/15/2014 11:39 AM, Stroller wrote:
> > On Wed, 14 May 2014, at 12:36 pm, Alexander Kapshuk 
<alexander.kapshuk@gmail.com> wrote:
> >>>> …
> >>>> If you like to check if RTL8192CE is enabled in  your kernel's .config
> >>>> file. If it isn't, you probably want to compile it as a module, and
> >>>> then add rtl8192ce to /etc/conf.d/modules as well.
> >>> 
> >>> Am pretty sure there's no need to add this one to /etc/conf.d/modules -
> >>> IME it'll just be found and loaded automagically by the kernel.
> >> 
> >> Thanks for pointing that out. I wasn't aware of that. As I mentioned in
> >> my previous post, I do not use genkernel myself.
> > 
> > Neither do I - for this reason I found it a little frustrating trying to
> > help in a recent thread, myself.
> > 
> > However, I'm pretty sure that loadable kernel modules behave the same
> > whether your kernel is built "by hand" or by genkernel - if you have
> > modules listed in /etc/conf.d/modules then I have to wonder if you
> > really need them there.
> > 
> > I haven't used that file for years, and I prefer to compile everything as
> > a module, too.
> > 
> > Stroller.
> 
> That's interesting. I wasn't aware of that either.
> 
> So far, I've just been following the instructions given in the handbook,
> section 7.d, which do recommend explicitly specifying the kernel modules
> to be loaded at boot time in /etc/conf.d/modules.
> 
> How does the kernel know then what modules to load at boot time, if it
> doesn't rely on /etc/conf.d/modules to supply the list of modules to be
> loaded?
> 
> Does it use udev, or some other mechanism for that?
> 
> Thanks.

I understand it is udev magic which probes the hardware and it fetches the 
corresponding module from the kernel, as long as it has been compiled.  
Incidentally, I noticed that I now have this running on my system:

/lib/systemd/systemd-udevd --daemon

-- 
Regards,
Mick

[-- Attachment #2: This is a digitally signed message part. --]
[-- Type: application/pgp-signature, Size: 490 bytes --]

Re: [gentoo-user] Having Trouble with Wireless Interface

[Alexander Kapshuk]

On 05/15/2014 10:50 PM, Mick wrote:
> On Thursday 15 May 2014 14:24:57 Alexander Kapshuk wrote:
>> On 05/15/2014 11:39 AM, Stroller wrote:
>>> On Wed, 14 May 2014, at 12:36 pm, Alexander Kapshuk 
> <alexander.kapshuk@gmail.com> wrote:
>>>>>> …
>>>>>> If you like to check if RTL8192CE is enabled in  your kernel's .config
>>>>>> file. If it isn't, you probably want to compile it as a module, and
>>>>>> then add rtl8192ce to /etc/conf.d/modules as well.
>>>>> Am pretty sure there's no need to add this one to /etc/conf.d/modules -
>>>>> IME it'll just be found and loaded automagically by the kernel.
>>>> Thanks for pointing that out. I wasn't aware of that. As I mentioned in
>>>> my previous post, I do not use genkernel myself.
>>> Neither do I - for this reason I found it a little frustrating trying to
>>> help in a recent thread, myself.
>>>
>>> However, I'm pretty sure that loadable kernel modules behave the same
>>> whether your kernel is built "by hand" or by genkernel - if you have
>>> modules listed in /etc/conf.d/modules then I have to wonder if you
>>> really need them there.
>>>
>>> I haven't used that file for years, and I prefer to compile everything as
>>> a module, too.
>>>
>>> Stroller.
>> That's interesting. I wasn't aware of that either.
>>
>> So far, I've just been following the instructions given in the handbook,
>> section 7.d, which do recommend explicitly specifying the kernel modules
>> to be loaded at boot time in /etc/conf.d/modules.
>>
>> How does the kernel know then what modules to load at boot time, if it
>> doesn't rely on /etc/conf.d/modules to supply the list of modules to be
>> loaded?
>>
>> Does it use udev, or some other mechanism for that?
>>
>> Thanks.
> I understand it is udev magic which probes the hardware and it fetches the 
> corresponding module from the kernel, as long as it has been compiled.  
> Incidentally, I noticed that I now have this running on my system:
>
> /lib/systemd/systemd-udevd --daemon
>
Understood. Thanks. I too have systemd-udevd running now that you
mention it.

[gentoo-user] Re: Having Trouble with Wireless Interface

[Jonathan Callen]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA512

On 05/15/2014 03:50 PM, Mick wrote:
> On Thursday 15 May 2014 14:24:57 Alexander Kapshuk wrote:
>> On 05/15/2014 11:39 AM, Stroller wrote:
>>> On Wed, 14 May 2014, at 12:36 pm, Alexander Kapshuk 
> <alexander.kapshuk@gmail.com> wrote:
>>>>>> …
>>>>>> If you like to check if RTL8192CE is enabled in  your kernel's .config
>>>>>> file. If it isn't, you probably want to compile it as a module, and
>>>>>> then add rtl8192ce to /etc/conf.d/modules as well.
>>>>>
>>>>> Am pretty sure there's no need to add this one to /etc/conf.d/modules -
>>>>> IME it'll just be found and loaded automagically by the kernel.
>>>>
>>>> Thanks for pointing that out. I wasn't aware of that. As I mentioned in
>>>> my previous post, I do not use genkernel myself.
>>>
>>> Neither do I - for this reason I found it a little frustrating trying to
>>> help in a recent thread, myself.
>>>
>>> However, I'm pretty sure that loadable kernel modules behave the same
>>> whether your kernel is built "by hand" or by genkernel - if you have
>>> modules listed in /etc/conf.d/modules then I have to wonder if you
>>> really need them there.
>>>
>>> I haven't used that file for years, and I prefer to compile everything as
>>> a module, too.
>>>
>>> Stroller.
>>
>> That's interesting. I wasn't aware of that either.
>>
>> So far, I've just been following the instructions given in the handbook,
>> section 7.d, which do recommend explicitly specifying the kernel modules
>> to be loaded at boot time in /etc/conf.d/modules.
>>
>> How does the kernel know then what modules to load at boot time, if it
>> doesn't rely on /etc/conf.d/modules to supply the list of modules to be
>> loaded?
>>
>> Does it use udev, or some other mechanism for that?
>>
>> Thanks.
> 
> I understand it is udev magic which probes the hardware and it fetches the 
> corresponding module from the kernel, as long as it has been compiled.  
> Incidentally, I noticed that I now have this running on my system:
> 
> /lib/systemd/systemd-udevd --daemon
> 

The actual udev magic in question is this line from
/lib/udev/rules.d/80-drivers.rules:

ENV{MODALIAS}=="?*", RUN{builtin}+="kmod load $env{MODALIAS}"

When a new device is seen by the kernel (which includes cold-plug on
boot), udev calls the equivalent of `modprobe ${MODALIAS}` (in reality,
the actual command is now just a call to libkmod, which is linked into
udev itself), where ${MODALIAS} is the contents of the file "modalias"
under the /sys directory describing that device.  This file may look
something like this (actual example from my machine):

pci:v00008086d00000416sv00001558sd00007104bc03sc00i00

This information (following the the initial "pci:", indicating that this
is a PCI device), can be split into multiple identifier/number pairs,
like so:

v  00008086
d  00000416
sv 00001558
sd 00007104
bc 03
sc 00
i  00

In this case I have vendor "00008086" (Intel Corporation), device
"00000416" (4th Gen Core Processor Integrated Graphics Controller),
subsystem vendor "00001558" (CLEVO/KAPOK Computer), subsystem device
"00007104" (not listed in pci.ids, sorry), base class "03" (Display
controller), sub class "00" (VGA compatible controller), and programming
interface "00" (VGA controller).

This information is then used to look up the module in
/lib/modules/$(uname -r)/modules.alias (actually, modules.alias.bin is
used if present to speed up the lookup).  This lookup finds the line:

alias pci:v00008086d00000416sv*sd*bc03sc*i* i915

As my card matches the glob in the second field in that line, the module
listed in the third field is loaded to handle the card.  The actual
modules.alias file is generated by depmod when the module is installed
by reading the information from the module itself.

- -- 
Jonathan Callen
123456789012345678901234567890123456789012345678901234567890123456789012
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/
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=Oswq
-----END PGP SIGNATURE-----

Re: [gentoo-user] Re: Having Trouble with Wireless Interface

[Alexander Kapshuk]

[-- Attachment #1: Type: text/plain, Size: 4276 bytes --]

On 05/18/2014 04:05 AM, Jonathan Callen wrote:
> On 05/15/2014 03:50 PM, Mick wrote:
> > On Thursday 15 May 2014 14:24:57 Alexander Kapshuk wrote:
> >> On 05/15/2014 11:39 AM, Stroller wrote:
> >>> On Wed, 14 May 2014, at 12:36 pm, Alexander Kapshuk
> > <alexander.kapshuk@gmail.com> wrote:
> >>>>>> ?
> >>>>>> If you like to check if RTL8192CE is enabled in  your kernel's
> .config
> >>>>>> file. If it isn't, you probably want to compile it as a module, and
> >>>>>> then add rtl8192ce to /etc/conf.d/modules as well.
> >>>>>
> >>>>> Am pretty sure there's no need to add this one to
> /etc/conf.d/modules -
> >>>>> IME it'll just be found and loaded automagically by the kernel.
> >>>>
> >>>> Thanks for pointing that out. I wasn't aware of that. As I
> mentioned in
> >>>> my previous post, I do not use genkernel myself.
> >>>
> >>> Neither do I - for this reason I found it a little frustrating
> trying to
> >>> help in a recent thread, myself.
> >>>
> >>> However, I'm pretty sure that loadable kernel modules behave the same
> >>> whether your kernel is built "by hand" or by genkernel - if you have
> >>> modules listed in /etc/conf.d/modules then I have to wonder if you
> >>> really need them there.
> >>>
> >>> I haven't used that file for years, and I prefer to compile
> everything as
> >>> a module, too.
> >>>
> >>> Stroller.
> >>
> >> That's interesting. I wasn't aware of that either.
> >>
> >> So far, I've just been following the instructions given in the
> handbook,
> >> section 7.d, which do recommend explicitly specifying the kernel
> modules
> >> to be loaded at boot time in /etc/conf.d/modules.
> >>
> >> How does the kernel know then what modules to load at boot time, if it
> >> doesn't rely on /etc/conf.d/modules to supply the list of modules to be
> >> loaded?
> >>
> >> Does it use udev, or some other mechanism for that?
> >>
> >> Thanks.
>
> > I understand it is udev magic which probes the hardware and it
> fetches the
> > corresponding module from the kernel, as long as it has been compiled.
> > Incidentally, I noticed that I now have this running on my system:
>
> > /lib/systemd/systemd-udevd --daemon
>
>
> The actual udev magic in question is this line from
> /lib/udev/rules.d/80-drivers.rules:
>
> ENV{MODALIAS}=="?*", RUN{builtin}+="kmod load $env{MODALIAS}"
>
> When a new device is seen by the kernel (which includes cold-plug on
> boot), udev calls the equivalent of `modprobe ${MODALIAS}` (in reality,
> the actual command is now just a call to libkmod, which is linked into
> udev itself), where ${MODALIAS} is the contents of the file "modalias"
> under the /sys directory describing that device.  This file may look
> something like this (actual example from my machine):
>
> pci:v00008086d00000416sv00001558sd00007104bc03sc00i00
>
> This information (following the the initial "pci:", indicating that this
> is a PCI device), can be split into multiple identifier/number pairs,
> like so:
>
> v  00008086
> d  00000416
> sv 00001558
> sd 00007104
> bc 03
> sc 00
> i  00
>
> In this case I have vendor "00008086" (Intel Corporation), device
> "00000416" (4th Gen Core Processor Integrated Graphics Controller),
> subsystem vendor "00001558" (CLEVO/KAPOK Computer), subsystem device
> "00007104" (not listed in pci.ids, sorry), base class "03" (Display
> controller), sub class "00" (VGA compatible controller), and programming
> interface "00" (VGA controller).
>
> This information is then used to look up the module in
> /lib/modules/$(uname -r)/modules.alias (actually, modules.alias.bin is
> used if present to speed up the lookup).  This lookup finds the line:
>
> alias pci:v00008086d00000416sv*sd*bc03sc*i* i915
>
> As my card matches the glob in the second field in that line, the module
> listed in the third field is loaded to handle the card.  The actual
> modules.alias file is generated by depmod when the module is installed
> by reading the information from the module itself.
>
>
Thanks for the explanation.

Just to double check I understood it correctly, there's no need to put
the list of kernel modules into /etc/conf.d/modules any longer, because
udev is aware of the modules that have been built and will load them by
consulting /lib/modules/$(uname -r)/modules.alias. Is that correct?

Thanks.


[-- Attachment #2: Type: text/html, Size: 6068 bytes --]

Re: [gentoo-user] Re: Having Trouble with Wireless Interface

[Mick]

[-- Attachment #1: Type: Text/Plain, Size: 5101 bytes --]

On Wednesday 21 May 2014 18:56:49 Alexander Kapshuk wrote:
> On 05/18/2014 04:05 AM, Jonathan Callen wrote:
> > On 05/15/2014 03:50 PM, Mick wrote:
> > > On Thursday 15 May 2014 14:24:57 Alexander Kapshuk wrote:
> > >> On 05/15/2014 11:39 AM, Stroller wrote:
> > >>> On Wed, 14 May 2014, at 12:36 pm, Alexander Kapshuk
> > > 
> > > <alexander.kapshuk@gmail.com> wrote:
> > >>>>>> ?
> > >>>>>> If you like to check if RTL8192CE is enabled in  your kernel's
> > 
> > .config
> > 
> > >>>>>> file. If it isn't, you probably want to compile it as a module,
> > >>>>>> and then add rtl8192ce to /etc/conf.d/modules as well.
> > >>>>> 
> > >>>>> Am pretty sure there's no need to add this one to
> > 
> > /etc/conf.d/modules -
> > 
> > >>>>> IME it'll just be found and loaded automagically by the kernel.
> > >>>> 
> > >>>> Thanks for pointing that out. I wasn't aware of that. As I
> > 
> > mentioned in
> > 
> > >>>> my previous post, I do not use genkernel myself.
> > >>> 
> > >>> Neither do I - for this reason I found it a little frustrating
> > 
> > trying to
> > 
> > >>> help in a recent thread, myself.
> > >>> 
> > >>> However, I'm pretty sure that loadable kernel modules behave the same
> > >>> whether your kernel is built "by hand" or by genkernel - if you have
> > >>> modules listed in /etc/conf.d/modules then I have to wonder if you
> > >>> really need them there.
> > >>> 
> > >>> I haven't used that file for years, and I prefer to compile
> > 
> > everything as
> > 
> > >>> a module, too.
> > >>> 
> > >>> Stroller.
> > >> 
> > >> That's interesting. I wasn't aware of that either.
> > >> 
> > >> So far, I've just been following the instructions given in the
> > 
> > handbook,
> > 
> > >> section 7.d, which do recommend explicitly specifying the kernel
> > 
> > modules
> > 
> > >> to be loaded at boot time in /etc/conf.d/modules.
> > >> 
> > >> How does the kernel know then what modules to load at boot time, if it
> > >> doesn't rely on /etc/conf.d/modules to supply the list of modules to
> > >> be loaded?
> > >> 
> > >> Does it use udev, or some other mechanism for that?
> > >> 
> > >> Thanks.
> > > 
> > > I understand it is udev magic which probes the hardware and it
> > 
> > fetches the
> > 
> > > corresponding module from the kernel, as long as it has been compiled.
> > > Incidentally, I noticed that I now have this running on my system:
> > > 
> > > /lib/systemd/systemd-udevd --daemon
> > 
> > The actual udev magic in question is this line from
> > /lib/udev/rules.d/80-drivers.rules:
> > 
> > ENV{MODALIAS}=="?*", RUN{builtin}+="kmod load $env{MODALIAS}"
> > 
> > When a new device is seen by the kernel (which includes cold-plug on
> > boot), udev calls the equivalent of `modprobe ${MODALIAS}` (in reality,
> > the actual command is now just a call to libkmod, which is linked into
> > udev itself), where ${MODALIAS} is the contents of the file "modalias"
> > under the /sys directory describing that device.  This file may look
> > something like this (actual example from my machine):
> > 
> > pci:v00008086d00000416sv00001558sd00007104bc03sc00i00
> > 
> > This information (following the the initial "pci:", indicating that this
> > is a PCI device), can be split into multiple identifier/number pairs,
> > like so:
> > 
> > v  00008086
> > d  00000416
> > sv 00001558
> > sd 00007104
> > bc 03
> > sc 00
> > i  00
> > 
> > In this case I have vendor "00008086" (Intel Corporation), device
> > "00000416" (4th Gen Core Processor Integrated Graphics Controller),
> > subsystem vendor "00001558" (CLEVO/KAPOK Computer), subsystem device
> > "00007104" (not listed in pci.ids, sorry), base class "03" (Display
> > controller), sub class "00" (VGA compatible controller), and programming
> > interface "00" (VGA controller).
> > 
> > This information is then used to look up the module in
> > /lib/modules/$(uname -r)/modules.alias (actually, modules.alias.bin is
> > used if present to speed up the lookup).  This lookup finds the line:
> > 
> > alias pci:v00008086d00000416sv*sd*bc03sc*i* i915
> > 
> > As my card matches the glob in the second field in that line, the module
> > listed in the third field is loaded to handle the card.  The actual
> > modules.alias file is generated by depmod when the module is installed
> > by reading the information from the module itself.
> 
> Thanks for the explanation.
> 
> Just to double check I understood it correctly, there's no need to put
> the list of kernel modules into /etc/conf.d/modules any longer, because
> udev is aware of the modules that have been built and will load them by
> consulting /lib/modules/$(uname -r)/modules.alias. Is that correct?
> 
> Thanks.

No, it is incorrect, or I better say incomplete.  There are some modules 
(netfilter, virtualbox, et al.) which will not be autoloaded.  You will need 
to add those in your /etc/conf.d/modules and make sure the syntax is correct 
for the kernel version that you intend to boot with.
-- 
Regards,
Mick

[-- Attachment #2: This is a digitally signed message part. --]
[-- Type: application/pgp-signature, Size: 490 bytes --]

[gentoo-user] Re: Having Trouble with Wireless Interface

[Jonathan Callen]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA512

On 05/21/2014 01:56 PM, Alexander Kapshuk wrote:
> Thanks for the explanation.
> 
> Just to double check I understood it correctly, there's no need to put
> the list of kernel modules into /etc/conf.d/modules any longer, because
> udev is aware of the modules that have been built and will load them by
> consulting /lib/modules/$(uname -r)/modules.alias. Is that correct?
> 
> Thanks.
> 
> 

You only need to list the modules in /etc/conf.d/modules (for OpenRC) or
/etc/modules-load.d/*.conf (for systemd) if they would not otherwise be
loaded.  Just about any module that provides a driver for hardware that
can be autodetected (that is, PCI, USB, etc.) will be auto-loaded by
udev.  Modules used to provide filters, etc. for iptables are autoloaded
by iptables itself as needed.  Some modules do not have anything that
would cause them to be autoloaded (such as the vbox-* modules from
VirtualBox), in which case you *would* need to explicitly load them.

- -- 
Jonathan Callen
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/
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=SJpi
-----END PGP SIGNATURE-----

Re: [gentoo-user] Re: Having Trouble with Wireless Interface

[Alexander Kapshuk]

[-- Attachment #1: Type: text/plain, Size: 1100 bytes --]

On 05/22/2014 06:34 AM, Jonathan Callen wrote:
> On 05/21/2014 01:56 PM, Alexander Kapshuk wrote:
> > Thanks for the explanation.
>
> > Just to double check I understood it correctly, there's no need to put
> > the list of kernel modules into /etc/conf.d/modules any longer, because
> > udev is aware of the modules that have been built and will load them by
> > consulting /lib/modules/$(uname -r)/modules.alias. Is that correct?
>
> > Thanks.
>
>
>
> You only need to list the modules in /etc/conf.d/modules (for OpenRC) or
> /etc/modules-load.d/*.conf (for systemd) if they would not otherwise be
> loaded.  Just about any module that provides a driver for hardware that
> can be autodetected (that is, PCI, USB, etc.) will be auto-loaded by
> udev.  Modules used to provide filters, etc. for iptables are autoloaded
> by iptables itself as needed.  Some modules do not have anything that
> would cause them to be autoloaded (such as the vbox-* modules from
> VirtualBox), in which case you *would* need to explicitly load them.
>
>
Understood. Thanks to all those who did respond to my query.




[-- Attachment #2: Type: text/html, Size: 1678 bytes --]

Re: [gentoo-user] Having Trouble with Wireless Interface

[Mick]

[-- Attachment #1: Type: Text/Plain, Size: 1001 bytes --]

On Monday 12 May 2014 20:31:15 Hunter Jozwiak wrote:
> Hi all. I got Espeakup to finally function, but I have a problem now
> with my Realtech 8188 WiFi adapter, Rev01, according to ifconfig. I
> know it shows up as wlp7s0 on an ifconfig, normally. But for what ever
> reason, it isn't showing up. I have, in my /etc/conf.d/net the line:
> wlp7s0="DHCP". When I run ifconfig wlp7s0 up, I get an error about how
> the device is not able to be found. The driver shows up as a module in
> the kernel.

After you fix your kernel as advised by others, also fix your /etc/conf.d/net.

To specify the use of DHCP you would typically use this syntax, which is case 
sensitive:

  config_wlp7s0="dhcp"

If you want to specify particular parameters to dhcp for this interface try 
something like this example:

  dhcpcd_wlp7s0="-t 45"


You should also spend some time reading through 
/usr/share/doc/netifrc-0.2.2/net.example.bz2 for more complex configurations.

-- 
Regards,
Mick

[-- Attachment #2: This is a digitally signed message part. --]
[-- Type: application/pgp-signature, Size: 490 bytes --]