On Friday 13 Mar 2015 00:38:56 Dale wrote:
> James wrote:
> > Mick <michaelkintzios <at> gmail.com> writes:
> >>> # sensors
> >>> radeon-pci-0100
> >>> Adapter: PCI adapter
> >>> temp1:        +36.0°C  (crit = +120.0°C, hyst = +90.0°C)
> >>> fam15h_power-pci-00c4
> >>> Adapter: PCI adapter
> >>> power1:       19.97 W  (crit = 125.19 W)
> >>> 
> >>> k10temp-pci-00c3
> >>> Adapter: PCI adapter
> >>> temp1:        +24.9°C  (high = +70.0°C)
> >>> 
> >>>                        (crit = +90.0°C, hyst = +87.0°C)
> >> 
> >> There should be more after these, showing your voltages and various MoBo
> >> sensors.  Can you check that it87 is actually loaded?  lsmod will tell
> >> you.
> > 
> > Oh, I just noticed this posting; Dale's latest posting caused me to
> > look at the thread again.
> > 
> > rc-status shows lm_sensors running, as does ps.
> > 
> > but  lsmod  is empty:
> > Module                  Size  Used by
> > 
> > /etc/conf.d/lm_sensors shows:
> > 
> > MODULE_0=fam15h_power
> > MODULE_1=it87
> > MODULE_2=k10temp
> > 
> > 
> > I think I have it 'compiled in'. Are you sure I should be
> > seeing more information?
> > 
> > "GA-990FXA-UD3" is the mobo.
> > 
> > 
> > James
> 
> I have a 970A-UD3P mobo and I use this under Hardware Monitoring support:
> 
> AMD Family 10h+ temperature sensor
> AMD Family 15h processor power
> ITE IT87xx and compatibles
> 
> Under bus support:
> 
> Intel PIIX4 and compatible (ATI/AMD/Serverworks/Broadcom/SMSC)
> 
> Our mobo isn't exactly the same but if they use the same chips, those
> should get you all the info you need.
> 
> I might add, I build everything into the kernel and I don't even install
> lm_sensors. I haven't installed that in ages.
> 
> Hope that helps.
> 
> Dale
> 
> :-)  :-)

I don't have the same MoBo and have compiled my corresponding chipset sensor 
driver as a module.  It doesn't load unless I manually modprobe it or set it 
up in /etc/conf.d/modules.  This is how many readings I get:

$ sensors
radeon-pci-0008 
Adapter: PCI adapter 
temp1:        +37.0°C  (crit = +120.0°C, hyst = +90.0°C) 

k10temp-pci-00c3 
Adapter: PCI adapter 
temp1:        +36.8°C  (high = +70.0°C) 
                       (crit = +70.0°C, hyst = +69.0°C) 

fam15h_power-pci-00c4 
Adapter: PCI adapter 
power1:           N/A  (crit =  95.09 W) 

nct6791-isa-0290 
Adapter: ISA adapter 
in0:                    +1.38 V  (min =  +0.00 V, max =  +1.74 V) 
in1:                    +1.03 V  (min =  +0.00 V, max =  +0.00 V)  ALARM 
in2:                    +3.34 V  (min =  +0.00 V, max =  +0.00 V)  ALARM 
in3:                    +3.34 V  (min =  +0.00 V, max =  +0.00 V)  ALARM 
in4:                    +1.01 V  (min =  +0.00 V, max =  +0.00 V)  ALARM 
in5:                    +2.04 V  (min =  +0.00 V, max =  +0.00 V)  ALARM 
in6:                    +0.28 V  (min =  +0.00 V, max =  +0.00 V)  ALARM 
in7:                    +3.44 V  (min =  +0.00 V, max =  +0.00 V)  ALARM 
in8:                    +3.33 V  (min =  +0.00 V, max =  +0.00 V)  ALARM 
in9:                    +0.00 V  (min =  +0.00 V, max =  +0.00 V) 
in10:                   +0.17 V  (min =  +0.00 V, max =  +0.00 V)  ALARM 
in11:                   +0.17 V  (min =  +0.00 V, max =  +0.00 V)  ALARM 
in12:                   +1.01 V  (min =  +0.00 V, max =  +0.00 V)  ALARM 
in13:                   +1.03 V  (min =  +0.00 V, max =  +0.00 V)  ALARM 
in14:                   +0.21 V  (min =  +0.00 V, max =  +0.00 V)  ALARM 
fan1:                  1036 RPM  (min =    0 RPM) 
fan2:                  1695 RPM  (min =    0 RPM) 
fan3:                  1001 RPM  (min =    0 RPM) 
SYSTIN:                 +31.0°C  (high =  +0.0°C, hyst =  +0.0°C)  ALARM  
sensor = thermistor 
CPUTIN:                 +47.0°C  (high = +80.0°C, hyst = +75.0°C)  sensor = 
thermistor 
AUXTIN0:               +106.0°C    sensor = thermistor 
AUXTIN1:               +105.0°C    sensor = thermistor 
AUXTIN2:               +105.0°C    sensor = thermistor 
AUXTIN3:               +106.0°C    sensor = thermistor 
PCH_CHIP_CPU_MAX_TEMP:   +0.0°C 
PCH_CHIP_TEMP:           +0.0°C 
PCH_CPU_TEMP:            +0.0°C 
PCH_MCH_TEMP:            +0.0°C 
intrusion0:            ALARM 
intrusion1:            ALARM 
beep_enable:           disabled

HTH.
-- 
Regards,
Mick