Re: [gentoo-user] Re: audio with TV crd

[Uwe Thiem <uwix@iway.na>]

On 24 July 2006 00:52, Nick Rout wrote:

> ivtv:  ==================== START INIT IVTV ====================
> ivtv:  version 0.4.4 (tagged release) loading
> ivtv:  Linux version: 2.6.15-chw-2 SMP preempt 586 gcc-3.3
> ivtv:  In case of problems please include the debug info between
> ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
> ivtv:  any module options, when mailing the ivtv-users mailinglist.
> ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)
> ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 10 (level, low)
> -> IRQ 10 ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
> ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
> tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
> cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
> **********cx25840 0-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
> ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
> wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
> tda9887 0-0043: chip found @ 0x86 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
> tveeprom 0-0050: The eeprom says no radio is present, but the tuner type
> tveeprom 0-0050: indicates otherwise. I will assume that radio is present.
> tveeprom 0-0050: Hauppauge model 26559, rev C260, serial# 2945285
> tveeprom 0-0050: tuner model is LG S001D MK3 (idx 60, type 38)
> tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom
> 0x74) tveeprom 0-0050: audio processor is CX25843 (idx 37)
> tveeprom 0-0050: decoder processor is CX25843 (idx 30)
> tveeprom 0-0050: has radio, has no IR remote
> *************ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv0: Encoder revision: 0x02050032
> ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
> ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
> ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
> ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
> total) ivtv0: Create encoder radio stream
> tuner 0-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
> ivtv0: Initialized WinTV PVR 150, card #0
> ivtv:  ====================  END INIT IVTV  ====================

Mine looks pretty much the same except that it detects the remote. Firmware 
gets loaded, all drivers get loaded, no errors.

Meanwhile I do have audio but very very faint if i raise everything to maximum 
(mixer, speaker amplifier, ivtvctl). 

I don't know. Maybe the hardware is fried.

Uwe

-- 
Mark Twain: I rather decline two drinks than a German adjective.
http://www.SysEx.com.na
-- 
gentoo-user@gentoo.org mailing list