Re: [gentoo-user] Re: lm_sensors problem

[Allan Spagnol Comar <allan.comar@gmail.com>]

Well it works, thanks !!!

On 2/13/06, Allan Spagnol Comar <allan.comar@gmail.com> wrote:
> I will try change the file and I got in touch about what happens
>
> On 2/12/06, Harm Geerts <harmgeerts@home.nl> wrote:
> > On Monday 13 February 2006 03:26, Allan Spagnol Comar wrote:
> > > Hi all,
> > >
> > > I had installed lm_sensors and kernel modules, now when I run sensors
> > > command I got:
> > >
> > > monstro ~ # sensors
> > > it8712-isa-0290
> > > Adapter: ISA adapter
> > > VCore 1:   +1.41 V  (min =  +1.42 V, max =  +1.57 V)   ALARM
> > > VCore 2:   +0.00 V  (min =  +2.40 V, max =  +2.61 V)   ALARM
> > > +3.3V:     +6.53 V  (min =  +3.14 V, max =  +3.46 V)   ALARM
> > > +5V:       +5.00 V  (min =  +4.76 V, max =  +5.24 V)
> > > +12V:     +11.84 V  (min = +11.39 V, max = +12.61 V)
> > > -12V:      -4.17 V  (min = -12.63 V, max = -11.41 V)   ALARM
> > > -5V:      -13.64 V  (min =  -5.26 V, max =  -4.77 V)   ALARM
> > > Stdby:     +4.89 V  (min =  +4.76 V, max =  +5.24 V)
> > > VBat:      +3.12 V
> > > fan1:        0 RPM  (min =    0 RPM, div = 8)
> > > fan2:        0 RPM  (min = 3013 RPM, div = 8)          ALARM
> > > fan3:     6750 RPM  (min = 3013 RPM, div = 8)
> > > M/B Temp:    +35 C  (low  =   +15 C, high =   +40 C)   sensor = thermistor
> > > CPU Temp:    +40 C  (low  =   +15 C, high =   +45 C)   sensor = thermistor
> > > Temp3:       +27 C  (low  =   +15 C, high =   +45 C)   sensor = thermistor
> > >
> > > how you all can see VCore2 is unavailable and -5 and -12 information
> > > seems to be switched,
> > >
> > > does anyone had a clue about it, I am running on a nvidia4 base
> > > motherboard.
> >
> > You'll need to change some settings in /etc/sensors.conf for your sensor chip.
> > Your output seems a lot like mine with a default config so I'll paste the
> > relevant part of my config, I have a Asus A8N SLI-Deluxe with a
> > it8712-isa-0290.
> >
> > After you've modified /etc/sensors.conf you need to run `sensors -s` for the
> > changes to take effect. You also need to run `sensors -s` after a reboot.
> > Unless you use the sensors init.d script you can add that command
> > to /etc/conf.d/local.start
> >
> > # cat /etc/sensors.conf
> >
> > chip "it87-*" "it8712-*"
> >
> > # Modified for Asus A8N SLI-Deluxe
> >
> > # Voltage monitors as advised in the It8705 data sheet
> >
> >     label in0 "VCore 1"
> >     label in1 "VCore 2"
> >     label in2 "+3.3V"
> >     label in3 "+5V"
> >     label in4 "+12V"
> >     label in5 "-5V"
> >     label in6 "-12V"
> >     label in7 "Stdby"
> >     label in8 "VBat"
> >
> >     # vid is not monitored by IT8705F
> >     # comment out if you have IT8712
> >     ignore  vid
> >     ignore  in1
> >
> > # Incubus Saturnus reports that the IT87 chip on Asus A7V8X-X seems
> > # to report the VCORE voltage approximately 0.05V higher than the board's
> > # BIOS does. Although it doesn't make much sense physically, uncommenting
> > # the next line should bring the readings in line with the BIOS' ones in
> > # this case.
> > # compute in0 -0.05+@ , @+0.05
> >
> > # If 3.3V reads 2X too high (Soyo Dragon and Asus A7V8X-X, for example),
> > # comment out following line.
> > #    compute in2   2*@ , @/2
> > #
> >     compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
> >     compute in4 ((30/10) +1)*@  , @/((30/10) +1)
> > # For this family of chips the negative voltage equation is different from
> > # the lm78.  The chip uses two external resistor for scaling but one is
> > # tied to a positive reference voltage.  See ITE8705/12 datasheet (SIS950
> > # data sheet is wrong)
> > # Vs = (1 + Rin/Rf) * Vin - (Rin/Rf) * Vref.
> > # Vref = 4.096 volts, Vin is voltage measured, Vs is actual voltage.
> >
> > # The next two are negative voltages (-12 and -5).
> > # The following formulas must be used. Unfortunately the datasheet
> > # does not give recommendations for Rin, Rf, but we can back into
> > # them based on a nominal +2V input to the chip, together with a 4.096V Vref.
> > # Formula:
> > #    actual V = (Vmeasured * (1 + Rin/Rf)) - (Vref * (Rin/Rf))
> > #    For -12V input use Rin/Rf = 6.68
> > #    For -5V input use Rin/Rf = 3.33
> > # Then you can convert the forumula to a standard form like:
> >     compute in5 (7.67 * @) - 27.36  ,  (@ + 27.36) / 7.67
> >     compute in6 (4.33 * @) - 13.64  ,  (@ + 13.64) / 4.33
> > #
> > # this much simpler version is reported to work for a
> > # Elite Group K7S5A board
> > #
> > #   compute in5 -(36/10)*@, -@/(36/10)
> > #   compute in6 -(56/10)*@, -@/(56/10)
> > #
> >     compute in7 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
> >
> >     set in0_min 1.4 * 0.95
> >     set in0_max 1.4 * 1.05
> >     set in1_min 2.4
> >     set in1_max 2.6
> >     set in2_min 3.3 * 0.95
> >     set in2_max 3.3 * 1.05
> >     set in3_min 5.0 * 0.95
> >     set in3_max 5.0 * 1.05
> >     set in4_min 12 * 0.95
> >     set in4_max 12 * 1.05
> >     set in5_max -5 * 0.95
> >     set in5_min -5 * 1.05
> >     set in6_max -12 * 0.95
> >     set in6_min -12 * 1.05
> >     set in7_min 5 * 0.95
> >     set in7_max 5 * 1.05
> >     #the chip does not support in8 min/max
> >
> > # Temperature
> > #
> > # Important - if your temperature readings are completely whacky
> > # you probably need to change the sensor type.
> > # Adujst and uncomment the appropriate lines below.
> > # The old method (modprobe it87 temp_type=0xXX) is no longer supported.
> > #
> > # 2 = thermistor; 3 = thermal diode; 0 = unused
> > #   set sensor1 3
> > #   set sensor2 3
> > #   set sensor3 3
> > # If a given sensor isn't used, you will probably want to ignore it
> > # (see ignore statement right below).
> >
> >     label temp1       "CPU Temp"
> >     set   temp1_over  50
> >     set   temp1_low   15
> >     label temp2       "MB Temp"
> >     set   temp2_over  45
> >     set   temp2_low   15
> > #    ignore temp3
> >     label temp3       "Temp3"
> >     set   temp3_over  40
> >     set   temp3_low   15
> >
> > # The A7V8X-X has temperatures inverted, and needs a conversion for
> > # CPU temp. Thanks to Preben Randhol for the formula.
> > #   label temp1       "CPU Temp"
> > #   label temp2       "M/B Temp"
> > #   compute temp1     (-15.096+1.4893*@), (@+15.096)/1.4893
> >
> > # The A7V600 also has temperatures inverted, and needs a different
> > # conversion for CPU temp. Thanks to Dariusz Jaszkowski for the formula.
> > #   label temp1       "CPU Temp"
> > #   label temp2       "M/B Temp"
> > #   compute temp1     (@+128)/3, (3*@-128)
> >
> > # Fans
> >     set fan1_min 0
> >     set fan2_min 3000
> >     ignore fan2
> >     ignore fan3
> >     set fan3_min 3000
> > --
> > gentoo-user@gentoo.org mailing list
> >
> >
>
>
> --
> An application asked:
> "Requeires Windows 9x, NT4 or better",
> so I´ve installed Linux
>


--
An application asked:
"Requeires Windows 9x, NT4 or better",
so I´ve installed Linux

-- 
gentoo-user@gentoo.org mailing list