On Friday 29 Jul 2016 12:20:14 james wrote:
> On 07/29/2016 09:27 AM, R0b0t1 wrote:
>
>
>
>
>
> I
> OK, so I have finally switch my posting to this email. Gmane.org is dead
> for now (hence my delayed responses).
>
> [1] https://lars.ingebrigtsen.no/2016/07/28/the-end-of-gmane/
>
> So in one thread, I'm going to post to variety of recent posts;
> recreated since I have a new email address now anyways and just got it
> setup with gentoo-user. (sorry if this makes the thread hard to follow.
>
> > Neil
> >
> > It's the ESP (EF00) that can be used as /boot, EF02 is a special
> >
> > partition that should exist but not be used.
>
> Agreed. The posted example partition tables (PT) were just an attempt
> to motivate any respondant to post an actual (PT) presented by whatever
> tool so I could actually see what I'm trying to drive to. Soon, later
> tonight or tomorrow, I'll post an actual attempt from recovered failures.
>
> > Tomh
> > The OP wants a partition scheme for both "standard" and efi firmware,
> > so he wants an EF02 (gdisk name) of 1MB and an EF00 (also gdisk name).
>
> Yes, this is a key point.
>
> > The OP wanted the EF02 to be mounted as "/boot" so it has to be
> > larger than 100MB in order to accomodate multiple kernels (and
> > possibly initramfs "thingies" as they're sometimes called here).
> >
> > It's the ESP (EF00) that can be used as /boot, EF02 is a
> > special partition that should exist but not be used.
>
> OK, my problem is I do not know exactly what this looks like. I am
> assuming I can do it all with gdisk (which is gptfdisk right)?
>
> So this is just a starting point of what the PT & fstab cold look like
>
> Number Start End Size Type File system Flags
> 1 1049kB 211MB 210MB primary ext2 boot
> 2 211MB 139GB 138GB primary linux-swap(v1)
> 3 139GB 952GB 813GB primary ext4
> 4 952GB 2000GB 1049GB primary ext4
>
> corresponding fstab::
>
> /dev/sda1 /boot ext2 defaults,noatime 0 2
> /dev/sda2 none swap sw 0 0
> /dev/sda3 / ext4 defaults,noatime 0 1
> /dev/sda4 /usr/local ext4 defaults,noatime 0 1
>
> > David Haller
> > You'd have to get rid of one of those partitions (I'd say /boot).
>
> OK, I was already thinking about placing /boot under '/' anyway, as
> many of the stage-4 images I will be using in the auto-image installs
> are commonly found as using just 2 partitions anyway ('/' and swap)
>
> The '/usr/local' will be optional depending on disk size and available
> space to provide this third partition. /usr/local will not be needed for
> boot(strap) and can be mounted after the systems is up. So /boot
> is part of / now.
>
> > Mick
> > It seems you did not use gdisk or a late version of parted to created
> > the partition table? Modern partition tools align the logical and
> > physical sectors to 4096B.
>
> Yep, I just 'dogged' the PT hoping someone would create and post what it
> should look like, or copy/paste a correct example from somewhere. Sorry
>
> >> 1 1049kB 211MB 210MB primary ext2 boot
> >
> > Instead of ext2 follow the guide for creating a FAT fs partition with
> > an EF00 partition type.
> > James should set the boot flag in the partition table for /dev/sda1
> > and mount it under /boot (or /boot/EFI) in fstab.
>
> I'm going to do away with a separate /boot for now and 'boot' partition
> will be moved under /.
>
> > R0b0t1
> >
> > > It seems you did not use gdisk or a late version of parted to
> >
> > created the partition table? Modern partition tools align the
> > logical and physical sectors to 4096B.
> >
> > It can be changed. SSDs are best used with 512B sectors. But, err...
>
> Well, proper alignment was automatically taken care of with newer tools?
> That sort of perfromance issue is also critical. Eventuall, SSD and usb3
> mmc and all sorts of other media will be used, depending on the embedded
> board's supported interface mix that will work with the vendor's (board)
> bootstrap code to bring up linux.
>
> > The protective MBR can point to another one and you can select which
> > GPT partitions are in it. But that's getting into some rube goldberg
> > action.
>
> Is this true if one is using grub-legacy?
>
> While I'm at it (gentoo specific) what is the difference in
> sys-boot/grub-static (0.96-r1 to 0.97-r12) and sys-boot/grub (0.97-r16)
> in slot zero?
>
> I'm assuming that sys-boot/grub-2.02_beta2-r9++ is all grub-2 with
> current enhancements.
>
>
> I do appreciate all the inputs, and appologize again for the
> transitioning emails, complicated by the demise of gmane.org (my fav
> reading/posting for gentoo-user).
>
> I'm going to post back as soon as I get an actually 2T disk setup with
> all of this advise, just to check what folks think and eventually with
> the results of booting a variety of mbr systems (efi and newer embedded
> systems as they are purchased.)
>
> I have a few SSD to experiment with now and may try some usb devices
> after the spinning rust PT is happy.
>
>
> James
I'm on the road to post fully, but here's an SSD with UEFI MoBo and GPT
tables:
=================
# gdisk /dev/sda
GPT fdisk (gdisk) version 1.0.1
Partition table scan:
MBR: protective
BSD: not present
APM: not present
GPT: present
Found valid GPT with protective MBR; using GPT.
Command (? for help): p
Disk /dev/sda: 468862128 sectors, 223.6 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): E682BFC8-0C85-459B-BA14-87F4E68CD711
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 468862094
Partitions will be aligned on 2048-sector boundaries
Total free space is 27368557 sectors (13.0 GiB)
Number Start (sector) End (sector) Size Code Name
1 2048 1093631 533.0 MiB EF00 ESP
2 1093632 43036671 20.0 GiB 8300 root
3 43036672 441495551 190.0 GiB 8300 home
==================================
The note about protective MBR is because it was created automatically with
gdisk.
eix -l fdisk
[I] sys-apps/gptfdisk
Available versions:
0.8.10 [ncurses static KERNEL="linux"]
~ 1.0.0 [ncurses static KERNEL="linux"]
1.0.1 [ncurses static KERNEL="linux"]
Installed versions: 1.0.1(10:39:35 28/05/16)(ncurses -static
KERNEL="linux")
Homepage: http://www.rodsbooks.com/gdisk/
Description: GPT partition table manipulator for Linux
Same deal but viewing it using fdisk:
=====================
# fdisk /dev/sda
Welcome to fdisk (util-linux 2.26.2).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Command (m for help): p
Disk /dev/sda: 223.6 GiB, 240057409536 bytes, 468862128 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: E682BFC8-0C85-459B-BA14-87F4E68CD711
Device Start End Sectors Size Type
/dev/sda1 2048 1093631 1091584 533M EFI System
/dev/sda2 1093632 43036671 41943040 20G Linux filesystem
/dev/sda3 43036672 441495551 398458880 190G Linux filesystem
==================================
and parted:
=========
parted /dev/sda
GNU Parted 3.2
Using /dev/sda
Welcome to GNU Parted! Type 'help' to view a list of commands.
(parted) print
Model: ATA OCZ-ARC100 (scsi)
Disk /dev/sda: 240GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Disk Flags:
Number Start End Size File system Name Flags
1 1049kB 560MB 559MB fat32 ESP boot, esp
2 560MB 22.0GB 21.5GB btrfs root
3 22.0GB 226GB 204GB btrfs home
==================================
I don't use grub on this MoBo, just the EFI stub. Hope this helps for now.
--
Regards,
Mick