[gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

[-- Attachment #1: Type: text/plain, Size: 4668 bytes --]

Hi,
  OK, I'm dead tired. I admit it - yaboot has kicked my butt this
time around. Can anyone help? I did post this problem here 2-3 weeks
ago but still haven't been able to solve the problem so I'm back to
the well for another drink.

  The machine is the original 80GB PPC Mac Mini. I used to run Gentoo
on it and it ran great for years so I know at one time yaboot worked
just fine. For various reasons I hadn't updated it in a long, long
time (2 years) and instead of trying to go through the Gentoo update
process which is difficult after that much time I decided to just do a
new install. I saved copies of my kernel config and etc/make.conf but
unfortunately, being primarily an x86 guy didn't think to save
yaboot.conf and fstab. I've now done 5 complete Gentoo installs,
starting over from scratch in case something I was doing was messing
things up but so far I cannot get the machine to boot. Every time, no
matter what I do at install time, I get a message

"Can't check if filesystem is mounted due to a missing mtab file"

A somewhat out of focus screen shot is shown here:

http://www.flickr.com/photos/29328985@N03/5014227831

Generally speaking I'm following the Gentoo PPC install guide located here:

http://www.gentoo.org/doc/en/handbook/handbook-ppc.xml?part=1&chap=10

I've tried both the yabootconfig method as well as manual route.
Nothing works for me so far. THey both fail the same way.

It's not in the photo but all the way through the boot the kernel
calls the hard drives /dev/hda so I'm assuming that's correct in
fstab.

The kernel is 2.6.34-gentoo-r2 and the kernel config file is attached.
ext3 is built into the kernel so that shouldn't be a problem. I built
the kernel using the older 2.6.31 kernel config I saved.

As a _hardware_ test I reinstalled the old OS X that came with the
machine and it boots fine. I blew it away and installed Ubuntu 10.04
for the PPC and it boots fine, but Ubuntu uses and initrc which I've
never used before with Gentoo. (And why on this machine as the
hardware is fixed has kernel drivers.)

I'm a long time Gentoo user. The main Gentoo install seems to work
fine on this machine. As best I can tell it's only the yaboot stuff
not booting that's holding me up from using this little machine again.

Can anyone see what I've done wrong?

Thanks,
Mark

livecd ~ # mount /dev/hda4 /mnt/gentoo
livecd ~ # mount -t proc none /mnt/gentoo/proc
livecd ~ # mount -o bind /dev /mnt/gentoo/dev
livecd ~ # mount -o bind /sys /mnt/gentoo/sys
livecd ~ # chroot /mnt/gentoo /bin/bash
livecd / # env-update
>>> Regenerating /etc/ld.so.cache...
livecd / # source /etc/profile
livecd / # export PS1="(chroot) $PS1"
(chroot) livecd / # cat /etc/yaboot.conf

boot=/dev/hda2
#device=/pci@f4000000/ata-6@d/disk@0:
device=hd:
timeout=30
install=/usr/lib/yaboot/yaboot
magicboot=/usr/lib/yaboot/ofboot

image=/boot/kernel-2.6.34-gentoo-r1
       label=Gentoo-2.6.34-r1
       partition=4
       root=/dev/hda4
       read-only
(chroot) livecd / # mac-fdisk -l /dev/hda
/dev/hda
       #                    type name                  length   base
   ( size )  system
/dev/hda1     Apple_partition_map Apple                     63 @ 1
   ( 31.5k)  Partition map
/dev/hda2         Apple_Bootstrap bootstrap               1600 @ 64
   (800.0k)  NewWorld bootblock
/dev/hda3         Apple_UNIX_SVR2 swap                 2097152 @ 1664
   (  1.0G)  Linux swap
/dev/hda4         Apple_UNIX_SVR2 root               154202672 @
2098816   ( 73.5G)  Linux native

Block size=512, Number of Blocks=156301488
DeviceType=0x0, DeviceId=0x0

(chroot) livecd / # cat /etc/fstab
/dev/hda4   /            ext3    noatime              0 1
/dev/hda3   none         swap    sw                   0 0

/dev/cdrom  /mnt/cdrom   auto    noauto,user          0 0

proc        /proc        proc    defaults             0 0
shm         /dev/shm     tmpfs   nodev,nosuid,noexec  0 0
(chroot) livecd / # ybin -v
ybin: Finding OpenFirmware device path to `/dev/hda2'...
ybin: Installing first stage bootstrap /usr/lib/yaboot/ofboot onto /dev/hda2...
ybin: Installing primary bootstrap /usr/lib/yaboot/yaboot onto /dev/hda2...
ybin: Installing /etc/yaboot.conf onto /dev/hda2...
ybin: Setting attributes on ofboot...
ybin: Setting attributes on yaboot...
ybin: Setting attributes on yaboot.conf...
ybin: Blessing /dev/hda2 with Holy Penguin Pee...
ybin: Updating OpenFirmware boot-device variable in nvram...
(chroot) livecd / # ls -al /boot/kernel*
-rwxr-xr-x 1 root root 5547992 Sep 22 11:06 /boot/kernel-2.6.34-gentoo-r1
(chroot) livecd / # exit
exit
livecd ~ # umount /mnt/gentoo/proc /mnt/gentoo/dev /mnt/gentoo/sys /mnt/gentoo
livecd ~ #
livecd ~ #

[-- Attachment #2: MacMini.config --]
[-- Type: application/octet-stream, Size: 56022 bytes --]

#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.34-gentoo-r1
# Wed Sep 22 10:51:26 2010
#
# CONFIG_PPC64 is not set

#
# Processor support
#
CONFIG_PPC_BOOK3S_32=y
# CONFIG_PPC_85xx is not set
# CONFIG_PPC_8xx is not set
# CONFIG_40x is not set
# CONFIG_44x is not set
# CONFIG_E200 is not set
CONFIG_PPC_BOOK3S=y
CONFIG_6xx=y
CONFIG_PPC_FPU=y
CONFIG_ALTIVEC=y
CONFIG_PPC_STD_MMU=y
CONFIG_PPC_STD_MMU_32=y
# CONFIG_PPC_MM_SLICES is not set
CONFIG_PPC_HAVE_PMU_SUPPORT=y
# CONFIG_SMP is not set
CONFIG_PPC32=y
CONFIG_WORD_SIZE=32
# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
CONFIG_MMU=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
# CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK is not set
CONFIG_IRQ_PER_CPU=y
CONFIG_NR_IRQS=512
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_ARCH_HAS_ILOG2_U32=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
CONFIG_PPC=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_NVRAM=y
CONFIG_SCHED_OMIT_FRAME_POINTER=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_PPC_OF=y
CONFIG_OF=y
CONFIG_PPC_UDBG_16550=y
# CONFIG_GENERIC_TBSYNC is not set
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_DTC=y
# CONFIG_DEFAULT_UIMAGE is not set
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
# CONFIG_PPC_DCR_NATIVE is not set
# CONFIG_PPC_DCR_MMIO is not set
CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_CONSTRUCTORS=y

#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_POSIX_MQUEUE_SYSCTL=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set

#
# RCU Subsystem
#
CONFIG_TREE_RCU=y
# CONFIG_TREE_PREEMPT_RCU is not set
# CONFIG_TINY_RCU is not set
# CONFIG_RCU_TRACE is not set
CONFIG_RCU_FANOUT=32
# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=15
# CONFIG_CGROUPS is not set
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
CONFIG_NAMESPACES=y
# CONFIG_UTS_NS is not set
# CONFIG_IPC_NS is not set
# CONFIG_USER_NS is not set
# CONFIG_PID_NS is not set
# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_RD_GZIP=y
CONFIG_RD_BZIP2=y
CONFIG_RD_LZMA=y
CONFIG_RD_LZO=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
# CONFIG_EMBEDDED is not set
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_PCSPKR_PLATFORM=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
CONFIG_HAVE_PERF_EVENTS=y

#
# Kernel Performance Events And Counters
#
# CONFIG_PERF_EVENTS is not set
# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_HAVE_DMA_API_DEBUG=y

#
# GCOV-based kernel profiling
#
# CONFIG_SLOW_WORK is not set
# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
# CONFIG_LBDAF is not set
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_DEADLINE is not set
# CONFIG_DEFAULT_CFQ is not set
CONFIG_DEFAULT_NOOP=y
CONFIG_DEFAULT_IOSCHED="noop"
# CONFIG_INLINE_SPIN_TRYLOCK is not set
# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
# CONFIG_INLINE_SPIN_LOCK is not set
# CONFIG_INLINE_SPIN_LOCK_BH is not set
# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
CONFIG_INLINE_SPIN_UNLOCK=y
# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
CONFIG_INLINE_SPIN_UNLOCK_IRQ=y
# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
# CONFIG_INLINE_READ_TRYLOCK is not set
# CONFIG_INLINE_READ_LOCK is not set
# CONFIG_INLINE_READ_LOCK_BH is not set
# CONFIG_INLINE_READ_LOCK_IRQ is not set
# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
CONFIG_INLINE_READ_UNLOCK=y
# CONFIG_INLINE_READ_UNLOCK_BH is not set
CONFIG_INLINE_READ_UNLOCK_IRQ=y
# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
# CONFIG_INLINE_WRITE_TRYLOCK is not set
# CONFIG_INLINE_WRITE_LOCK is not set
# CONFIG_INLINE_WRITE_LOCK_BH is not set
# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
CONFIG_INLINE_WRITE_UNLOCK=y
# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
CONFIG_INLINE_WRITE_UNLOCK_IRQ=y
# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
# CONFIG_MUTEX_SPIN_ON_OWNER is not set
CONFIG_FREEZER=y

#
# Platform support
#
CONFIG_PPC_CHRP=y
# CONFIG_MPC5121_ADS is not set
# CONFIG_MPC5121_GENERIC is not set
# CONFIG_PPC_MPC52xx is not set
CONFIG_PPC_PMAC=y
# CONFIG_PPC_CELL is not set
# CONFIG_PPC_CELL_NATIVE is not set
# CONFIG_PPC_82xx is not set
# CONFIG_PQ2ADS is not set
# CONFIG_PPC_83xx is not set
# CONFIG_PPC_86xx is not set
# CONFIG_EMBEDDED6xx is not set
# CONFIG_AMIGAONE is not set
CONFIG_PPC_NATIVE=y
CONFIG_PPC_OF_BOOT_TRAMPOLINE=y
# CONFIG_UDBG_RTAS_CONSOLE is not set
# CONFIG_IPIC is not set
CONFIG_MPIC=y
# CONFIG_MPIC_WEIRD is not set
CONFIG_PPC_I8259=y
CONFIG_PPC_RTAS=y
CONFIG_RTAS_ERROR_LOGGING=y
CONFIG_PPC_RTAS_DAEMON=y
CONFIG_RTAS_PROC=y
# CONFIG_MMIO_NVRAM is not set
CONFIG_PPC_MPC106=y
# CONFIG_PPC_970_NAP is not set
# CONFIG_PPC_INDIRECT_IO is not set
# CONFIG_GENERIC_IOMAP is not set
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
# CONFIG_CPU_FREQ_DEBUG is not set
# CONFIG_CPU_FREQ_STAT is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_CPU_FREQ_GOV_USERSPACE=m
CONFIG_CPU_FREQ_GOV_ONDEMAND=m
# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set

#
# CPU Frequency drivers
#
CONFIG_CPU_FREQ_PMAC=y
CONFIG_PPC601_SYNC_FIX=y
# CONFIG_TAU is not set
# CONFIG_FSL_ULI1575 is not set
# CONFIG_SIMPLE_GPIO is not set

#
# Kernel options
#
CONFIG_HIGHMEM=y
# CONFIG_NO_HZ is not set
# CONFIG_HIGH_RES_TIMERS is not set
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
# CONFIG_HZ_300 is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
# CONFIG_SCHED_HRTICK is not set
# CONFIG_PREEMPT_NONE is not set
CONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT is not set
CONFIG_BINFMT_ELF=y
# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
# CONFIG_HAVE_AOUT is not set
# CONFIG_BINFMT_MISC is not set
# CONFIG_IOMMU_HELPER is not set
# CONFIG_SWIOTLB is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_ARCH_HAS_WALK_MEMORY=y
CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_SPARSE_IRQ=y
CONFIG_MAX_ACTIVE_REGIONS=32
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_VIRT_TO_BUS=y
# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_PPC_4K_PAGES=y
# CONFIG_PPC_16K_PAGES is not set
# CONFIG_PPC_64K_PAGES is not set
# CONFIG_PPC_256K_PAGES is not set
CONFIG_FORCE_MAX_ZONEORDER=11
CONFIG_PROC_DEVICETREE=y
CONFIG_CMDLINE_BOOL=y
CONFIG_CMDLINE="console=ttyS0,115200,8n1 console=tty0 init=/linuxrc looptype=squashfs loop=/image.squashfs udev nodevfs cdroot root=/dev/ram"
CONFIG_EXTRA_TARGETS=""
CONFIG_ARCH_WANTS_FREEZER_CONTROL=y
CONFIG_PM=y
# CONFIG_PM_DEBUG is not set
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
# CONFIG_HIBERNATION is not set
CONFIG_APM_EMULATION=y
# CONFIG_PM_RUNTIME is not set
CONFIG_PM_OPS=y
CONFIG_SECCOMP=y
CONFIG_ISA_DMA_API=y

#
# Bus options
#
# CONFIG_ISA is not set
CONFIG_ZONE_DMA=y
# CONFIG_NEED_DMA_MAP_STATE is not set
CONFIG_GENERIC_ISA_DMA=y
CONFIG_PPC_INDIRECT_PCI=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCI_SYSCALL=y
# CONFIG_PCIEPORTBUS is not set
CONFIG_ARCH_SUPPORTS_MSI=y
# CONFIG_PCI_MSI is not set
# CONFIG_PCI_STUB is not set
# CONFIG_PCI_IOV is not set
CONFIG_PCCARD=m
CONFIG_PCMCIA=m
CONFIG_PCMCIA_LOAD_CIS=y
CONFIG_CARDBUS=y

#
# PC-card bridges
#
CONFIG_YENTA=m
CONFIG_YENTA_O2=y
CONFIG_YENTA_RICOH=y
CONFIG_YENTA_TI=y
CONFIG_YENTA_ENE_TUNE=y
CONFIG_YENTA_TOSHIBA=y
# CONFIG_PD6729 is not set
# CONFIG_I82092 is not set
CONFIG_PCCARD_NONSTATIC=m
# CONFIG_HOTPLUG_PCI is not set
# CONFIG_HAS_RAPIDIO is not set

#
# Advanced setup
#
# CONFIG_ADVANCED_OPTIONS is not set

#
# Default settings for advanced configuration options are used
#
CONFIG_LOWMEM_SIZE=0x30000000
CONFIG_PAGE_OFFSET=0xc0000000
CONFIG_KERNEL_START=0xc0000000
CONFIG_PHYSICAL_START=0x00000000
CONFIG_TASK_SIZE=0xc0000000
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
# CONFIG_XFRM_STATISTICS is not set
CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=m
# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
CONFIG_INET_LRO=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
# CONFIG_IPV6_ROUTER_PREF is not set
# CONFIG_IPV6_OPTIMISTIC_DAD is not set
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
# CONFIG_IPV6_MIP6 is not set
CONFIG_INET6_XFRM_TUNNEL=m
CONFIG_INET6_TUNNEL=m
CONFIG_INET6_XFRM_MODE_TRANSPORT=m
CONFIG_INET6_XFRM_MODE_TUNNEL=m
CONFIG_INET6_XFRM_MODE_BEET=m
# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
CONFIG_IPV6_SIT=m
# CONFIG_IPV6_SIT_6RD is not set
CONFIG_IPV6_NDISC_NODETYPE=y
CONFIG_IPV6_TUNNEL=m
# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_IPV6_MROUTE is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_NET_DSA is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_PHONET is not set
# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
# CONFIG_DCB is not set

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
# CONFIG_IRDA is not set
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_HIDP=m

#
# Bluetooth device drivers
#
# CONFIG_BT_HCIBTUSB is not set
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
# CONFIG_BT_HCIUART_LL is not set
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_BT_HCIBFUSB=m
CONFIG_BT_HCIDTL1=m
CONFIG_BT_HCIBT3C=m
CONFIG_BT_HCIBLUECARD=m
CONFIG_BT_HCIBTUART=m
CONFIG_BT_HCIVHCI=m
# CONFIG_BT_MRVL is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
# CONFIG_LIB80211 is not set

#
# CFG80211 needs to be enabled for MAC80211
#
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
CONFIG_FIRMWARE_IN_KERNEL=y
CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
CONFIG_OF_FLATTREE=y
CONFIG_OF_DYNAMIC=y
CONFIG_OF_DEVICE=y
CONFIG_OF_I2C=y
CONFIG_OF_MDIO=m
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_FD=m
CONFIG_MAC_FLOPPY=m
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
CONFIG_BLK_DEV_DAC960=m
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m

#
# DRBD disabled because PROC_FS, INET or CONNECTOR not selected
#
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_SX8=m
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=8192
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_AD525X_DPOT is not set
# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_HP_ILO is not set
# CONFIG_ISL29003 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_DS1682 is not set
# CONFIG_C2PORT is not set

#
# EEPROM support
#
# CONFIG_EEPROM_AT24 is not set
# CONFIG_EEPROM_LEGACY is not set
# CONFIG_EEPROM_MAX6875 is not set
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_CB710_CORE is not set
CONFIG_HAVE_IDE=y
CONFIG_IDE=y

#
# Please see Documentation/ide/ide.txt for help/info on IDE drives
#
CONFIG_IDE_XFER_MODE=y
CONFIG_IDE_TIMINGS=y
CONFIG_IDE_ATAPI=y
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_IDE_GD=y
CONFIG_IDE_GD_ATA=y
# CONFIG_IDE_GD_ATAPI is not set
# CONFIG_BLK_DEV_IDECS is not set
# CONFIG_BLK_DEV_DELKIN is not set
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_IDE_PROC_FS=y

#
# IDE chipset support/bugfixes
#
# CONFIG_BLK_DEV_PLATFORM is not set
CONFIG_BLK_DEV_IDEDMA_SFF=y

#
# PCI IDE chipsets support
#
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_PCIBUS_ORDER=y
CONFIG_BLK_DEV_OFFBOARD=y
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
CONFIG_BLK_DEV_CMD64X=m
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
CONFIG_BLK_DEV_HPT366=m
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT8172 is not set
# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
CONFIG_BLK_DEV_PDC202XX_OLD=m
CONFIG_BLK_DEV_PDC202XX_NEW=m
# CONFIG_BLK_DEV_SVWKS is not set
CONFIG_BLK_DEV_SIIMAGE=m
# CONFIG_BLK_DEV_SL82C105 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=m
# CONFIG_BLK_DEV_TC86C001 is not set
CONFIG_BLK_DEV_IDE_PMAC=y
CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y
CONFIG_BLK_DEV_IDEDMA=y

#
# SCSI device support
#
CONFIG_SCSI_MOD=y
CONFIG_RAID_ATTRS=m
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
CONFIG_SCSI_NETLINK=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
# CONFIG_CHR_DEV_SCH is not set
CONFIG_SCSI_MULTI_LUN=y
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
CONFIG_SCSI_WAIT_SCAN=m

#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=y
CONFIG_SCSI_FC_ATTRS=m
CONFIG_SCSI_ISCSI_ATTRS=m
CONFIG_SCSI_SAS_ATTRS=m
CONFIG_SCSI_SAS_LIBSAS=m
# CONFIG_SCSI_SAS_ATA is not set
CONFIG_SCSI_SAS_HOST_SMP=y
CONFIG_SCSI_SAS_LIBSAS_DEBUG=y
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_BE2ISCSI is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_HPSA is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_3W_SAS is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=32
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
CONFIG_AIC7XXX_DEBUG_ENABLE=y
CONFIG_AIC7XXX_DEBUG_MASK=0
CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_MPT2SAS is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_FCOE is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_MESH is not set
# CONFIG_SCSI_MAC53C94 is not set
# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_PM8001 is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_BFA_FC is not set
# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=m
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
CONFIG_SATA_AHCI=m
CONFIG_SATA_SIL24=m
CONFIG_ATA_SFF=y
CONFIG_SATA_SVW=m
CONFIG_ATA_PIIX=m
CONFIG_SATA_MV=m
CONFIG_SATA_NV=m
CONFIG_PDC_ADMA=m
CONFIG_SATA_QSTOR=m
CONFIG_SATA_PROMISE=m
CONFIG_SATA_SX4=m
CONFIG_SATA_SIL=m
CONFIG_SATA_SIS=m
CONFIG_SATA_ULI=m
CONFIG_SATA_VIA=m
CONFIG_SATA_VITESSE=m
# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_LEGACY is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PCMCIA is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_SIL680 is not set
CONFIG_PATA_SIS=m
# CONFIG_PATA_TOSHIBA is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
# CONFIG_PATA_PLATFORM is not set
# CONFIG_PATA_SCH is not set
# CONFIG_PATA_MACIO is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_AUTODETECT=y
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
CONFIG_MD_RAID10=m
CONFIG_MD_RAID456=m
CONFIG_MD_RAID6_PQ=m
# CONFIG_ASYNC_RAID6_TEST is not set
CONFIG_MD_MULTIPATH=m
CONFIG_MD_FAULTY=m
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
CONFIG_DM_MIRROR=m
# CONFIG_DM_LOG_USERSPACE is not set
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
# CONFIG_DM_MULTIPATH_QL is not set
# CONFIG_DM_MULTIPATH_ST is not set
# CONFIG_DM_DELAY is not set
# CONFIG_DM_UEVENT is not set
# CONFIG_FUSION is not set

#
# IEEE 1394 (FireWire) support
#

#
# You can enable one or both FireWire driver stacks.
#

#
# The newer stack is recommended.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_MACINTOSH_DRIVERS=y
CONFIG_ADB=y
CONFIG_ADB_CUDA=y
CONFIG_ADB_PMU=y
CONFIG_ADB_PMU_LED=y
CONFIG_ADB_PMU_LED_IDE=y
CONFIG_PMAC_APM_EMU=y
CONFIG_PMAC_MEDIABAY=y
CONFIG_PMAC_BACKLIGHT=y
CONFIG_PMAC_BACKLIGHT_LEGACY=y
CONFIG_ADB_MACIO=y
CONFIG_INPUT_ADBHID=y
CONFIG_MAC_EMUMOUSEBTN=y
CONFIG_THERM_WINDTUNNEL=y
CONFIG_THERM_ADT746X=y
CONFIG_WINDFARM=y
# CONFIG_ANSLCD is not set
# CONFIG_PMAC_RACKMETER is not set
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
# CONFIG_VETH is not set
# CONFIG_ARCNET is not set
CONFIG_PHYLIB=m

#
# MII PHY device drivers
#
# CONFIG_MARVELL_PHY is not set
# CONFIG_DAVICOM_PHY is not set
# CONFIG_QSEMI_PHY is not set
# CONFIG_LXT_PHY is not set
# CONFIG_CICADA_PHY is not set
# CONFIG_VITESSE_PHY is not set
# CONFIG_SMSC_PHY is not set
# CONFIG_BROADCOM_PHY is not set
# CONFIG_ICPLUS_PHY is not set
# CONFIG_REALTEK_PHY is not set
# CONFIG_NATIONAL_PHY is not set
# CONFIG_STE10XP is not set
# CONFIG_LSI_ET1011C_PHY is not set
# CONFIG_MICREL_PHY is not set
# CONFIG_MDIO_BITBANG is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
CONFIG_MACE=y
# CONFIG_MACE_AAUI_PORT is not set
CONFIG_BMAC=y
CONFIG_HAPPYMEAL=m
CONFIG_SUNGEM=y
# CONFIG_CASSINI is not set
CONFIG_NET_VENDOR_3COM=y
# CONFIG_VORTEX is not set
# CONFIG_TYPHOON is not set
# CONFIG_ETHOC is not set
# CONFIG_DNET is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_KSZ884X_PCI is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_R6040 is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SMSC9420 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_KS8842 is not set
# CONFIG_KS8851_MLL is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
# CONFIG_ATL2 is not set
# CONFIG_XILINX_EMACLITE is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
# CONFIG_WLAN is not set

#
# Enable WiMAX (Networking options) to see the WiMAX drivers
#

#
# USB Network Adapters
#
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
# CONFIG_USB_NET_CDC_EEM is not set
# CONFIG_USB_NET_DM9601 is not set
# CONFIG_USB_NET_SMSC75XX is not set
# CONFIG_USB_NET_SMSC95XX is not set
# CONFIG_USB_NET_GL620A is not set
CONFIG_USB_NET_NET1080=m
# CONFIG_USB_NET_PLUSB is not set
CONFIG_USB_NET_MCS7830=m
# CONFIG_USB_NET_RNDIS_HOST is not set
# CONFIG_USB_NET_CDC_SUBSET is not set
CONFIG_USB_NET_ZAURUS=m
# CONFIG_USB_NET_INT51X1 is not set
# CONFIG_USB_IPHETH is not set
# CONFIG_USB_SIERRA_NET is not set
# CONFIG_NET_PCMCIA is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_VMXNET3 is not set
# CONFIG_ISDN is not set
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set
# CONFIG_INPUT_SPARSEKMAP is not set

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_ADP5588 is not set
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_LM8323 is not set
# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
# CONFIG_MOUSE_PS2_ELANTECH is not set
# CONFIG_MOUSE_PS2_SENTELIC is not set
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_BCM5974 is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_MOUSE_SYNAPTICS_I2C is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
# CONFIG_INPUT_ATI_REMOTE is not set
# CONFIG_INPUT_ATI_REMOTE2 is not set
# CONFIG_INPUT_KEYSPAN_REMOTE is not set
# CONFIG_INPUT_POWERMATE is not set
# CONFIG_INPUT_YEALINK is not set
# CONFIG_INPUT_CM109 is not set
# CONFIG_INPUT_UINPUT is not set

#
# Hardware I/O ports
#
CONFIG_SERIO=y
# CONFIG_SERIO_I8042 is not set
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_SERIO_XILINX_XPS_PS2 is not set
# CONFIG_SERIO_ALTERA_PS2 is not set
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_NOZOMI is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=m
CONFIG_SERIAL_8250_PCI=m
# CONFIG_SERIAL_8250_CS is not set
CONFIG_SERIAL_8250_NR_UARTS=2
CONFIG_SERIAL_8250_RUNTIME_UARTS=2
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
# CONFIG_SERIAL_UARTLITE is not set
CONFIG_SERIAL_CORE=m
# CONFIG_SERIAL_PMACZILOG is not set
# CONFIG_SERIAL_JSM is not set
# CONFIG_SERIAL_OF_PLATFORM is not set
# CONFIG_SERIAL_TIMBERDALE is not set
# CONFIG_SERIAL_GRLIB_GAISLER_APBUART is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_BRIQ_PANEL is not set
# CONFIG_HVC_RTAS is not set
# CONFIG_HVC_UDBG is not set
# CONFIG_IPMI_HANDLER is not set
CONFIG_HW_RANDOM=y
# CONFIG_HW_RANDOM_TIMERIOMEM is not set
CONFIG_NVRAM=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set

#
# PCMCIA character devices
#
# CONFIG_SYNCLINK_CS is not set
# CONFIG_CARDMAN_4000 is not set
# CONFIG_CARDMAN_4040 is not set
# CONFIG_IPWIRELESS is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
CONFIG_I2C_ALGOBIT=y

#
# I2C Hardware Bus support
#

#
# PC SMBus host controller drivers
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_ISCH is not set
# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set

#
# Mac SMBus host controller drivers
#
CONFIG_I2C_HYDRA=m
CONFIG_I2C_POWERMAC=y

#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
CONFIG_I2C_MPC=m
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_XILINX is not set

#
# External I2C/SMBus adapter drivers
#
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_TAOS_EVM is not set
# CONFIG_I2C_TINY_USB is not set

#
# Other I2C/SMBus bus drivers
#
# CONFIG_I2C_PCA_PLATFORM is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_SPI is not set

#
# PPS support
#
# CONFIG_PPS is not set
CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
# CONFIG_GPIOLIB is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=m
# CONFIG_HWMON_VID is not set
# CONFIG_HWMON_DEBUG_CHIP is not set

#
# Native drivers
#
# CONFIG_SENSORS_AD7414 is not set
# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1029 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ADT7411 is not set
# CONFIG_SENSORS_ADT7462 is not set
# CONFIG_SENSORS_ADT7470 is not set
# CONFIG_SENSORS_ADT7475 is not set
# CONFIG_SENSORS_ASC7621 is not set
# CONFIG_SENSORS_AMS is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_F75375S is not set
# CONFIG_SENSORS_G760A is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM63 is not set
# CONFIG_SENSORS_LM73 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_LM93 is not set
# CONFIG_SENSORS_LTC4215 is not set
# CONFIG_SENSORS_LTC4245 is not set
# CONFIG_SENSORS_LM95241 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_MAX6650 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_DME1737 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_ADS7828 is not set
# CONFIG_SENSORS_AMC6821 is not set
# CONFIG_SENSORS_THMC50 is not set
# CONFIG_SENSORS_TMP401 is not set
# CONFIG_SENSORS_TMP421 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83L786NG is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_SENSORS_LIS3_I2C is not set
# CONFIG_THERMAL is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y

#
# Sonics Silicon Backplane
#
CONFIG_SSB=m
CONFIG_SSB_SPROM=y
CONFIG_SSB_PCIHOST_POSSIBLE=y
CONFIG_SSB_PCIHOST=y
# CONFIG_SSB_B43_PCI_BRIDGE is not set
CONFIG_SSB_PCMCIAHOST_POSSIBLE=y
# CONFIG_SSB_PCMCIAHOST is not set
# CONFIG_SSB_DEBUG is not set
CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
CONFIG_SSB_DRIVER_PCICORE=y

#
# Multifunction device drivers
#
# CONFIG_MFD_CORE is not set
# CONFIG_MFD_88PM860X is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_TWL4030_CORE is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_PMIC_ADP5520 is not set
# CONFIG_MFD_MAX8925 is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_WM8994 is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_AB3100_CORE is not set
# CONFIG_LPC_SCH is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set

#
# Graphics support
#
CONFIG_AGP=m
CONFIG_AGP_UNINORTH=m
CONFIG_VGA_ARB=y
CONFIG_VGA_ARB_MAX_GPUS=16
CONFIG_DRM=m
CONFIG_DRM_KMS_HELPER=m
CONFIG_DRM_TTM=m
CONFIG_DRM_TDFX=m
CONFIG_DRM_R128=m
CONFIG_DRM_RADEON=m
# CONFIG_DRM_RADEON_KMS is not set
CONFIG_DRM_MGA=m
CONFIG_DRM_SIS=m
# CONFIG_DRM_VIA is not set
# CONFIG_DRM_SAVAGE is not set
CONFIG_VGASTATE=y
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=y
# CONFIG_FB_BOOT_VESA_SUPPORT is not set
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
# CONFIG_FB_SVGALIB is not set
CONFIG_FB_MACMODES=y
CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
# CONFIG_FB_TILEBLITTING is not set

#
# Frame buffer hardware drivers
#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
CONFIG_FB_OF=y
CONFIG_FB_CONTROL=y
CONFIG_FB_PLATINUM=y
CONFIG_FB_VALKYRIE=y
CONFIG_FB_CT65550=y
CONFIG_FB_ASILIANT=y
CONFIG_FB_IMSTT=y
CONFIG_FB_VGA16=y
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_NVIDIA=y
CONFIG_FB_NVIDIA_I2C=y
# CONFIG_FB_NVIDIA_DEBUG is not set
CONFIG_FB_NVIDIA_BACKLIGHT=y
CONFIG_FB_RIVA=y
CONFIG_FB_RIVA_I2C=y
# CONFIG_FB_RIVA_DEBUG is not set
CONFIG_FB_RIVA_BACKLIGHT=y
# CONFIG_FB_MATROX is not set
CONFIG_FB_RADEON=y
CONFIG_FB_RADEON_I2C=y
CONFIG_FB_RADEON_BACKLIGHT=y
# CONFIG_FB_RADEON_DEBUG is not set
CONFIG_FB_ATY128=y
CONFIG_FB_ATY128_BACKLIGHT=y
CONFIG_FB_ATY=y
CONFIG_FB_ATY_CT=y
CONFIG_FB_ATY_GENERIC_LCD=y
CONFIG_FB_ATY_GX=y
CONFIG_FB_ATY_BACKLIGHT=y
# CONFIG_FB_S3 is not set
CONFIG_FB_SAVAGE=y
# CONFIG_FB_SAVAGE_I2C is not set
# CONFIG_FB_SAVAGE_ACCEL is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_VIA is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
CONFIG_FB_3DFX=y
# CONFIG_FB_3DFX_ACCEL is not set
CONFIG_FB_3DFX_I2C=y
CONFIG_FB_VOODOO1=y
# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_CARMINE is not set
# CONFIG_FB_IBM_GXT4500 is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FB_METRONOME is not set
# CONFIG_FB_MB862XX is not set
# CONFIG_FB_BROADSHEET is not set
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=m
# CONFIG_LCD_ILI9320 is not set
# CONFIG_LCD_PLATFORM is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
CONFIG_BACKLIGHT_GENERIC=y

#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VGACON_SOFT_SCROLLBACK is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
# CONFIG_FB_CON_DECOR is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_SOUND=m
# CONFIG_SOUND_OSS_CORE is not set
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
# CONFIG_SND_SEQUENCER is not set
# CONFIG_SND_MIXER_OSS is not set
# CONFIG_SND_PCM_OSS is not set
# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
CONFIG_SND_VMASTER=y
# CONFIG_SND_RAWMIDI_SEQ is not set
# CONFIG_SND_OPL3_LIB_SEQ is not set
# CONFIG_SND_OPL4_LIB_SEQ is not set
# CONFIG_SND_SBAWE_SEQ is not set
# CONFIG_SND_EMU10K1_SEQ is not set
CONFIG_SND_DRIVERS=y
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
CONFIG_SND_PCI=y
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AW2 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_OXYGEN is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS5530 is not set
# CONFIG_SND_CS5535AUDIO is not set
# CONFIG_SND_CTXFI is not set
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
# CONFIG_SND_INDIGOIOX is not set
# CONFIG_SND_INDIGODJX is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_HDA_INTEL is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_HIFIER is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_LX6464ES is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VIRTUOSO is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
CONFIG_SND_PPC=y
CONFIG_SND_POWERMAC=m
CONFIG_SND_POWERMAC_AUTO_DRC=y
CONFIG_SND_AOA=m
CONFIG_SND_AOA_FABRIC_LAYOUT=m
CONFIG_SND_AOA_ONYX=m
CONFIG_SND_AOA_TAS=m
CONFIG_SND_AOA_TOONIE=m
CONFIG_SND_AOA_SOUNDBUS=m
CONFIG_SND_AOA_SOUNDBUS_I2S=m
CONFIG_SND_USB=y
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_UA101 is not set
# CONFIG_SND_USB_USX2Y is not set
# CONFIG_SND_USB_CAIAQ is not set
CONFIG_SND_PCMCIA=y
# CONFIG_SND_VXPOCKET is not set
# CONFIG_SND_PDAUDIOCF is not set
# CONFIG_SND_SOC is not set
# CONFIG_SOUND_PRIME is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HIDRAW is not set

#
# USB Input Devices
#
CONFIG_USB_HID=m
# CONFIG_HID_PID is not set
CONFIG_USB_HIDDEV=y

#
# Special HID drivers
#
# CONFIG_HID_3M_PCT is not set
CONFIG_HID_A4TECH=m
CONFIG_HID_APPLE=m
CONFIG_HID_BELKIN=m
CONFIG_HID_CHERRY=m
CONFIG_HID_CHICONY=m
CONFIG_HID_CYPRESS=m
CONFIG_HID_DRAGONRISE=m
# CONFIG_DRAGONRISE_FF is not set
CONFIG_HID_EZKEY=m
CONFIG_HID_KYE=m
CONFIG_HID_GYRATION=m
CONFIG_HID_TWINHAN=m
CONFIG_HID_KENSINGTON=m
CONFIG_HID_LOGITECH=m
# CONFIG_LOGITECH_FF is not set
# CONFIG_LOGIRUMBLEPAD2_FF is not set
# CONFIG_LOGIG940_FF is not set
# CONFIG_HID_MAGICMOUSE is not set
CONFIG_HID_MICROSOFT=m
# CONFIG_HID_MOSART is not set
CONFIG_HID_MONTEREY=m
CONFIG_HID_NTRIG=m
CONFIG_HID_ORTEK=m
CONFIG_HID_PANTHERLORD=m
# CONFIG_PANTHERLORD_FF is not set
CONFIG_HID_PETALYNX=m
# CONFIG_HID_QUANTA is not set
CONFIG_HID_SAMSUNG=m
CONFIG_HID_SONY=m
# CONFIG_HID_STANTUM is not set
CONFIG_HID_SUNPLUS=m
CONFIG_HID_GREENASIA=m
# CONFIG_GREENASIA_FF is not set
CONFIG_HID_SMARTJOYPLUS=m
# CONFIG_SMARTJOYPLUS_FF is not set
CONFIG_HID_TOPSEED=m
CONFIG_HID_THRUSTMASTER=m
# CONFIG_THRUSTMASTER_FF is not set
CONFIG_HID_WACOM=m
CONFIG_HID_ZEROPLUS=m
# CONFIG_ZEROPLUS_FF is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set
# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
CONFIG_USB_MON=m
# CONFIG_USB_WUSB is not set
# CONFIG_USB_WUSB_CBAF is not set

#
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
# CONFIG_USB_XHCI_HCD is not set
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_XPS_USB_HCD_XILINX is not set
CONFIG_USB_EHCI_HCD_PPC_OF=y
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=m
CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
CONFIG_USB_OHCI_HCD_PPC_OF=y
CONFIG_USB_OHCI_HCD_PCI=y
# CONFIG_USB_OHCI_HCD_SSB is not set
CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
CONFIG_USB_U132_HCD=m
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_WHCI_HCD is not set
# CONFIG_USB_HWA_HCD is not set

#
# Enable Host or Gadget support to see Inventra options
#

#
# USB Device Class drivers
#
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
# CONFIG_USB_WDM is not set
# CONFIG_USB_TMC is not set

#
# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#

#
# also be needed; see USB_STORAGE Help for more info
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
CONFIG_USB_STORAGE_FREECOM=m
CONFIG_USB_STORAGE_ISD200=m
CONFIG_USB_STORAGE_USBAT=m
CONFIG_USB_STORAGE_SDDR09=m
CONFIG_USB_STORAGE_SDDR55=m
CONFIG_USB_STORAGE_JUMPSHOT=m
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_LIBUSUAL is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set

#
# USB port drivers
#
CONFIG_USB_SERIAL=m
# CONFIG_USB_EZUSB is not set
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_AIRCABLE=m
# CONFIG_USB_SERIAL_ARK3116 is not set
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_CH341 is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_CP210X is not set
# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
# CONFIG_USB_SERIAL_FUNSOFT is not set
# CONFIG_USB_SERIAL_VISOR is not set
# CONFIG_USB_SERIAL_IPAQ is not set
# CONFIG_USB_SERIAL_IR is not set
# CONFIG_USB_SERIAL_EDGEPORT is not set
# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
# CONFIG_USB_SERIAL_GARMIN is not set
CONFIG_USB_SERIAL_IPW=m
# CONFIG_USB_SERIAL_IUU is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
# CONFIG_USB_SERIAL_KEYSPAN is not set
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
CONFIG_USB_SERIAL_MOS7720=m
CONFIG_USB_SERIAL_MOS7840=m
# CONFIG_USB_SERIAL_MOTOROLA is not set
# CONFIG_USB_SERIAL_NAVMAN is not set
# CONFIG_USB_SERIAL_PL2303 is not set
# CONFIG_USB_SERIAL_OTI6858 is not set
# CONFIG_USB_SERIAL_QCAUX is not set
# CONFIG_USB_SERIAL_QUALCOMM is not set
# CONFIG_USB_SERIAL_SPCP8X5 is not set
# CONFIG_USB_SERIAL_HP4X is not set
# CONFIG_USB_SERIAL_SAFE is not set
# CONFIG_USB_SERIAL_SIEMENS_MPI is not set
CONFIG_USB_SERIAL_SIERRAWIRELESS=m
# CONFIG_USB_SERIAL_SYMBOL is not set
# CONFIG_USB_SERIAL_TI is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
# CONFIG_USB_SERIAL_OPTION is not set
CONFIG_USB_SERIAL_OMNINET=m
# CONFIG_USB_SERIAL_OPTICON is not set
# CONFIG_USB_SERIAL_VIVOPAY_SERIAL is not set
# CONFIG_USB_SERIAL_DEBUG is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_SEVSEG is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_IDMOUSE is not set
CONFIG_USB_FTDI_ELAN=m
CONFIG_USB_APPLEDISPLAY=m
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_GADGET is not set

#
# OTG and related infrastructure
#
# CONFIG_NOP_USB_XCEIV is not set
# CONFIG_UWB is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y

#
# LED drivers
#
# CONFIG_LEDS_PCA9532 is not set
# CONFIG_LEDS_LP3944 is not set
# CONFIG_LEDS_PCA955X is not set
# CONFIG_LEDS_BD2802 is not set
CONFIG_LEDS_TRIGGERS=y

#
# LED Triggers
#
CONFIG_LEDS_TRIGGER_TIMER=y
CONFIG_LEDS_TRIGGER_IDE_DISK=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set

#
# iptables trigger is under Netfilter config (LED target)
#
# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
# CONFIG_RTC_DEBUG is not set

#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
# CONFIG_RTC_DRV_TEST is not set

#
# I2C RTC drivers
#
# CONFIG_RTC_DRV_DS1307 is not set
# CONFIG_RTC_DRV_DS1374 is not set
# CONFIG_RTC_DRV_DS1672 is not set
# CONFIG_RTC_DRV_MAX6900 is not set
# CONFIG_RTC_DRV_RS5C372 is not set
# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set
# CONFIG_RTC_DRV_BQ32K is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
# CONFIG_RTC_DRV_RX8025 is not set

#
# SPI RTC drivers
#

#
# Platform RTC drivers
#
# CONFIG_RTC_DRV_CMOS is not set
# CONFIG_RTC_DRV_DS1286 is not set
# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T35 is not set
# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_MSM6242 is not set
# CONFIG_RTC_DRV_BQ4802 is not set
# CONFIG_RTC_DRV_RP5C01 is not set
# CONFIG_RTC_DRV_V3020 is not set

#
# on-CPU RTC drivers
#
# CONFIG_RTC_DRV_GENERIC is not set
# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set

#
# TI VLYNQ
#
# CONFIG_STAGING is not set

#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
# CONFIG_EXT4_FS is not set
CONFIG_JBD=y
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
CONFIG_QUOTA=y
# CONFIG_QUOTA_NETLINK_INTERFACE is not set
CONFIG_PRINT_QUOTA_WARNING=y
# CONFIG_QUOTA_DEBUG is not set
CONFIG_QUOTA_TREE=m
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=m
CONFIG_QUOTACTL=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
CONFIG_FUSE_FS=m
# CONFIG_CUSE is not set
CONFIG_GENERIC_ACL=y

#
# Caches
#
# CONFIG_FSCACHE is not set

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
# CONFIG_ZISOFS is not set
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-15"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
# CONFIG_NTFS_RW is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
CONFIG_HFS_FS=y
CONFIG_HFSPLUS_FS=y
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_LOGFS is not set
# CONFIG_CRAMFS is not set
CONFIG_SQUASHFS=y
# CONFIG_SQUASHFS_EMBEDDED is not set
CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
CONFIG_UFS_FS=m
# CONFIG_UFS_FS_WRITE is not set
# CONFIG_UFS_DEBUG is not set
# CONFIG_NETWORK_FILESYSTEMS is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
CONFIG_AMIGA_PARTITION=y
# CONFIG_ATARI_PARTITION is not set
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
# CONFIG_SYSV68_PARTITION is not set
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf8"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=y
# CONFIG_DLM is not set
# CONFIG_BINARY_PRINTF is not set

#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_GENERIC_FIND_LAST_BIT=y
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
# CONFIG_CRC_T10DIF is not set
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_LZO_DECOMPRESS=y
CONFIG_DECOMPRESS_GZIP=y
CONFIG_DECOMPRESS_BZIP2=y
CONFIG_DECOMPRESS_LZMA=y
CONFIG_DECOMPRESS_LZO=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y

#
# Kernel hacking
#
CONFIG_PRINTK_TIME=y
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_MEMORY_INIT=y
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_PPC_DISABLE_WERROR is not set
CONFIG_PPC_WERROR=y
CONFIG_PRINT_STACK_DEPTH=64
# CONFIG_IRQSTACKS is not set
CONFIG_BOOTX_TEXT=y
# CONFIG_PPC_EARLY_DEBUG is not set

#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
# CONFIG_DEFAULT_SECURITY_SELINUX is not set
# CONFIG_DEFAULT_SECURITY_SMACK is not set
# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
CONFIG_DEFAULT_SECURITY_DAC=y
CONFIG_DEFAULT_SECURITY=""
CONFIG_XOR_BLOCKS=m
CONFIG_ASYNC_CORE=m
CONFIG_ASYNC_MEMCPY=m
CONFIG_ASYNC_XOR=m
CONFIG_ASYNC_PQ=m
CONFIG_ASYNC_RAID6_RECOV=m
CONFIG_CRYPTO=y

#
# Crypto core or helper
#
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=m
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER=m
CONFIG_CRYPTO_BLKCIPHER2=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_PCOMP=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_MANAGER2=y
# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_WORKQUEUE=y
# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_AUTHENC=m
# CONFIG_CRYPTO_TEST is not set

#
# Authenticated Encryption with Associated Data
#
# CONFIG_CRYPTO_CCM is not set
# CONFIG_CRYPTO_GCM is not set
# CONFIG_CRYPTO_SEQIV is not set

#
# Block modes
#
CONFIG_CRYPTO_CBC=m
# CONFIG_CRYPTO_CTR is not set
# CONFIG_CRYPTO_CTS is not set
CONFIG_CRYPTO_ECB=m
# CONFIG_CRYPTO_LRW is not set
# CONFIG_CRYPTO_PCBC is not set
# CONFIG_CRYPTO_XTS is not set

#
# Hash modes
#
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
# CONFIG_CRYPTO_VMAC is not set

#
# Digest
#
CONFIG_CRYPTO_CRC32C=m
# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_MICHAEL_MIC=m
# CONFIG_CRYPTO_RMD128 is not set
# CONFIG_CRYPTO_RMD160 is not set
# CONFIG_CRYPTO_RMD256 is not set
# CONFIG_CRYPTO_RMD320 is not set
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_WP512 is not set

#
# Ciphers
#
CONFIG_CRYPTO_AES=m
# CONFIG_CRYPTO_ANUBIS is not set
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_BLOWFISH=m
# CONFIG_CRYPTO_CAMELLIA is not set
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_DES=m
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_SALSA20 is not set
# CONFIG_CRYPTO_SEED is not set
CONFIG_CRYPTO_SERPENT=m
# CONFIG_CRYPTO_TEA is not set
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m

#
# Compression
#
CONFIG_CRYPTO_DEFLATE=m
# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set

#
# Random Number Generation
#
# CONFIG_CRYPTO_ANSI_CPRNG is not set
CONFIG_CRYPTO_HW=y
# CONFIG_CRYPTO_DEV_HIFN_795X is not set
# CONFIG_PPC_CLOCK is not set
# CONFIG_VIRTUALIZATION is not set

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Joseph Jezak]

 On 09/22/10 18:59, Mark Knecht wrote:
> Hi,
>   OK, I'm dead tired. I admit it - yaboot has kicked my butt this
> time around. Can anyone help? I did post this problem here 2-3 weeks
> ago but still haven't been able to solve the problem so I'm back to
> the well for another drink.
>
>   The machine is the original 80GB PPC Mac Mini. I used to run Gentoo
> on it and it ran great for years so I know at one time yaboot worked
> just fine. For various reasons I hadn't updated it in a long, long
> time (2 years) and instead of trying to go through the Gentoo update
> process which is difficult after that much time I decided to just do a
> new install. I saved copies of my kernel config and etc/make.conf but
> unfortunately, being primarily an x86 guy didn't think to save
> yaboot.conf and fstab. I've now done 5 complete Gentoo installs,
> starting over from scratch in case something I was doing was messing
> things up but so far I cannot get the machine to boot. Every time, no
> matter what I do at install time, I get a message
>
> "Can't check if filesystem is mounted due to a missing mtab file"
>
> A somewhat out of focus screen shot is shown here:
>
> http://www.flickr.com/photos/29328985@N03/5014227831
>
> Generally speaking I'm following the Gentoo PPC install guide located here:
>
> http://www.gentoo.org/doc/en/handbook/handbook-ppc.xml?part=1&chap=10
>
> I've tried both the yabootconfig method as well as manual route.
> Nothing works for me so far. THey both fail the same way.
>
> It's not in the photo but all the way through the boot the kernel
> calls the hard drives /dev/hda so I'm assuming that's correct in
> fstab.
>
> The kernel is 2.6.34-gentoo-r2 and the kernel config file is attached.
> ext3 is built into the kernel so that shouldn't be a problem. I built
> the kernel using the older 2.6.31 kernel config I saved.
>
> As a _hardware_ test I reinstalled the old OS X that came with the
> machine and it boots fine. I blew it away and installed Ubuntu 10.04
> for the PPC and it boots fine, but Ubuntu uses and initrc which I've
> never used before with Gentoo. (And why on this machine as the
> hardware is fixed has kernel drivers.)
>
> I'm a long time Gentoo user. The main Gentoo install seems to work
> fine on this machine. As best I can tell it's only the yaboot stuff
> not booting that's holding me up from using this little machine again.
>
> Can anyone see what I've done wrong?
>
> Thanks,
> Mark
>
> livecd ~ # mount /dev/hda4 /mnt/gentoo
> livecd ~ # mount -t proc none /mnt/gentoo/proc
> livecd ~ # mount -o bind /dev /mnt/gentoo/dev
> livecd ~ # mount -o bind /sys /mnt/gentoo/sys
> livecd ~ # chroot /mnt/gentoo /bin/bash
> livecd / # env-update
>>>> Regenerating /etc/ld.so.cache...
> livecd / # source /etc/profile
> livecd / # export PS1="(chroot) $PS1"
> (chroot) livecd / # cat /etc/yaboot.conf
>
> boot=/dev/hda2
> #device=/pci@f4000000/ata-6@d/disk@0:
> device=hd:
> timeout=30
> install=/usr/lib/yaboot/yaboot
> magicboot=/usr/lib/yaboot/ofboot
>
> image=/boot/kernel-2.6.34-gentoo-r1
>        label=Gentoo-2.6.34-r1
>        partition=4
>        root=/dev/hda4
>        read-only
> (chroot) livecd / # mac-fdisk -l /dev/hda
> /dev/hda
>        #                    type name                  length   base
>    ( size )  system
> /dev/hda1     Apple_partition_map Apple                     63 @ 1
>    ( 31.5k)  Partition map
> /dev/hda2         Apple_Bootstrap bootstrap               1600 @ 64
>    (800.0k)  NewWorld bootblock
> /dev/hda3         Apple_UNIX_SVR2 swap                 2097152 @ 1664
>    (  1.0G)  Linux swap
> /dev/hda4         Apple_UNIX_SVR2 root               154202672 @
> 2098816   ( 73.5G)  Linux native
>
> Block size=512, Number of Blocks=156301488
> DeviceType=0x0, DeviceId=0x0
>
> (chroot) livecd / # cat /etc/fstab
> /dev/hda4   /            ext3    noatime              0 1
> /dev/hda3   none         swap    sw                   0 0
>
> /dev/cdrom  /mnt/cdrom   auto    noauto,user          0 0
>
> proc        /proc        proc    defaults             0 0
> shm         /dev/shm     tmpfs   nodev,nosuid,noexec  0 0
> (chroot) livecd / # ybin -v
> ybin: Finding OpenFirmware device path to `/dev/hda2'...
> ybin: Installing first stage bootstrap /usr/lib/yaboot/ofboot onto /dev/hda2...
> ybin: Installing primary bootstrap /usr/lib/yaboot/yaboot onto /dev/hda2...
> ybin: Installing /etc/yaboot.conf onto /dev/hda2...
> ybin: Setting attributes on ofboot...
> ybin: Setting attributes on yaboot...
> ybin: Setting attributes on yaboot.conf...
> ybin: Blessing /dev/hda2 with Holy Penguin Pee...
> ybin: Updating OpenFirmware boot-device variable in nvram...
> (chroot) livecd / # ls -al /boot/kernel*
> -rwxr-xr-x 1 root root 5547992 Sep 22 11:06 /boot/kernel-2.6.34-gentoo-r1
> (chroot) livecd / # exit
> exit
> livecd ~ # umount /mnt/gentoo/proc /mnt/gentoo/dev /mnt/gentoo/sys /mnt/gentoo
> livecd ~ #
> livecd ~ #
After looking at the screen shot, I think I have a different idea as to
why it might be failing and I don't think it's Yaboot.  If you've gotten
to init, yaboot's job is already done.

Can you boot the install CD and chroot into the install again? When you
get it up and running, check to see if fsck.ext3 exists. Even if it
does, re-emerge e2fsprogs and see if that helps.
-Joe

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Wed, Sep 22, 2010 at 6:33 PM, Joseph Jezak <josejx@gentoo.org> wrote:
>  On 09/22/10 18:59, Mark Knecht wrote:
>> Hi,
>>   OK, I'm dead tired. I admit it - yaboot has kicked my butt this
>> time around. Can anyone help? I did post this problem here 2-3 weeks
>> ago but still haven't been able to solve the problem so I'm back to
>> the well for another drink.
>>
>>   The machine is the original 80GB PPC Mac Mini. I used to run Gentoo
>> on it and it ran great for years so I know at one time yaboot worked
>> just fine. For various reasons I hadn't updated it in a long, long
>> time (2 years) and instead of trying to go through the Gentoo update
>> process which is difficult after that much time I decided to just do a
>> new install. I saved copies of my kernel config and etc/make.conf but
>> unfortunately, being primarily an x86 guy didn't think to save
>> yaboot.conf and fstab. I've now done 5 complete Gentoo installs,
>> starting over from scratch in case something I was doing was messing
>> things up but so far I cannot get the machine to boot. Every time, no
>> matter what I do at install time, I get a message
>>
>> "Can't check if filesystem is mounted due to a missing mtab file"
>>
>> A somewhat out of focus screen shot is shown here:
>>
>> http://www.flickr.com/photos/29328985@N03/5014227831
>>
>> Generally speaking I'm following the Gentoo PPC install guide located here:
>>
>> http://www.gentoo.org/doc/en/handbook/handbook-ppc.xml?part=1&chap=10
<SNIP>

> After looking at the screen shot, I think I have a different idea as to
> why it might be failing and I don't think it's Yaboot.  If you've gotten
> to init, yaboot's job is already done.
>
> Can you boot the install CD and chroot into the install again? When you
> get it up and running, check to see if fsck.ext3 exists. Even if it
> does, re-emerge e2fsprogs and see if that helps.
> -Joe

Very interesting. OK - I'm in the chroot now and reinstalling
e2fsprogs as you suggest. I'll reboot in a minute and check if it
helped. (OK - I rebooted and it didn't fix anything unfortunately. Too
bad. Thanks for the idea though.)

I was wondering if this was one of those things where device names
were changing. They were hda all through the install, which is
different from the Install Guide. I've tried to adjust my yaboot.conf
file accordingly but maybe it cannot find the disk at that point
because the name changed or something. I cannot see anything in the
boot screen to indicate that but I suppose it's possible.

While I'm here in the chroot I decided to poke around a bit. Note that
section 9d of the install guide says that e2fsprogs is already
installed as part of the system and indeed it appears to be as shown
below. However I note that I cannot run updatedb for slocate without
also getting a message about /etc/mtab not existing. Should mtab exist
withing the chroot?

(chroot) livecd / # emerge -pv e2fsprogs

These are the packages that would be merged, in order:

Calculating dependencies... done!
[ebuild   R   ] sys-fs/e2fsprogs-1.41.11  USE="nls" 4,368 kB

Total: 1 package (1 reinstall), Size of downloads: 4,368 kB
(chroot) livecd / # slocate fsck.*
slocate: fatal error: Could not find user database
'/var/lib/slocate/slocate.db':  No such file or directory
(chroot) livecd / # updatedb
updatedb: fatal error: load_file: Could not open file: /etc/mtab: No
such file or directory
updatedb: fatal error: parse_fs_exclude: Could not load file data: /etc/mtab
^C
(chroot) livecd / #


Indeed, on a different system /etc/mtab exists:

gandalf ~ # cat /etc/mtab
/dev/sda3 / ext3 rw,noatime,commit=0 0 0
proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0
sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0
udev /dev tmpfs rw,nosuid,relatime,size=10240k,mode=755 0 0
devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620 0 0
/dev/sda5 /home/herb ext3 rw,noatime,commit=0 0 0
shm /dev/shm tmpfs rw,noexec,nosuid,nodev 0 0
none /proc/fs/vmblock/mountPoint vmblock rw 0 0
gandalf ~ #

However on my MacMini it simply doesn't exist:

(chroot) livecd / # ls -la /etc/mtab
ls: cannot access /etc/mtab: No such file or directory
(chroot) livecd / #

So the question is what provides mtab? Have I missed some step in the
install process 5 times? Man, that would be embarrassing but I'd
gladly suffer the shame if I got the machine working! ;-)

Thanks for your help. Still looking.

Cheers,
Mark

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[kahl]

Mark,

 > However I note that I cannot run updatedb for slocate without
 > also getting a message about /etc/mtab not existing. Should mtab exist
 > withing the chroot?

For certain things, it seems to be needed --- the amd64 handbook includes a
way to get it among the grub instructions.

By the way, if I recall correctly, you once mentioned you had an ubuntu on
that machine with grub working --- I would just reuse that grub for booting
gentoo. (I have done this before on amd64, but not on any Mac.)


Wolfram

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Thu, Sep 23, 2010 at 5:05 AM,  <kahl@cas.mcmaster.ca> wrote:
> Mark,
>
>  > However I note that I cannot run updatedb for slocate without
>  > also getting a message about /etc/mtab not existing. Should mtab exist
>  > withing the chroot?
>
> For certain things, it seems to be needed --- the amd64 handbook includes a
> way to get it among the grub instructions.
>
> By the way, if I recall correctly, you once mentioned you had an ubuntu on
> that machine with grub working --- I would just reuse that grub for booting
> gentoo. (I have done this before on amd64, but not on any Mac.)
>
>
> Wolfram
>
>
Wolfram,
   On first reading I would have said 'he's crazy!' because grub is
for x86/PC architecture only, right? At least I think that's the case
with the original grub.

   However apparently grub2 does now run (sort of) on PowerPC:

http://grub.enbug.org/TestingOnPowerPC

   I think it's more in a testing phase, and if Joe or others help me
work out what I'm doing wrong then I won't need grub2, but given a bit
of time it might be interesting to try out. Unfortunately the known
bug list might make it hard for someone at my experience level.

   Looking in portage it doesn't seem to be available so I'd have to
look for an overlay that might have it.

Thanks,
Mark

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Joseph Jezak]

 On 09/23/10 13:55, Mark Knecht wrote:
> On Thu, Sep 23, 2010 at 5:05 AM,  <kahl@cas.mcmaster.ca> wrote:
>> Mark,
>>
>>  > However I note that I cannot run updatedb for slocate without
>>  > also getting a message about /etc/mtab not existing. Should mtab exist
>>  > withing the chroot?
>>
>> For certain things, it seems to be needed --- the amd64 handbook includes a
>> way to get it among the grub instructions.
>>
>> By the way, if I recall correctly, you once mentioned you had an ubuntu on
>> that machine with grub working --- I would just reuse that grub for booting
>> gentoo. (I have done this before on amd64, but not on any Mac.)
>>
>>
>> Wolfram
>>
>>
> Wolfram,
>    On first reading I would have said 'he's crazy!' because grub is
> for x86/PC architecture only, right? At least I think that's the case
> with the original grub.
>
>    However apparently grub2 does now run (sort of) on PowerPC:
>
> http://grub.enbug.org/TestingOnPowerPC
>
>    I think it's more in a testing phase, and if Joe or others help me
> work out what I'm doing wrong then I won't need grub2, but given a bit
> of time it might be interesting to try out. Unfortunately the known
> bug list might make it hard for someone at my experience level.
>
>    Looking in portage it doesn't seem to be available so I'd have to
> look for an overlay that might have it.
>
> Thanks,
> Mark
>
>
Yeah, grub2 isn't really user ready yet. It does work on ppc, but cannot
boot OSX (at least last time I tried it it couldn't).

-Joe

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Joseph Jezak]

 On 09/22/10 23:33, Mark Knecht wrote:
> On Wed, Sep 22, 2010 at 6:33 PM, Joseph Jezak <josejx@gentoo.org> wrote:
>>  On 09/22/10 18:59, Mark Knecht wrote:
>>> Hi,
>>>   OK, I'm dead tired. I admit it - yaboot has kicked my butt this
>>> time around. Can anyone help? I did post this problem here 2-3 weeks
>>> ago but still haven't been able to solve the problem so I'm back to
>>> the well for another drink.
>>>
>>>   The machine is the original 80GB PPC Mac Mini. I used to run Gentoo
>>> on it and it ran great for years so I know at one time yaboot worked
>>> just fine. For various reasons I hadn't updated it in a long, long
>>> time (2 years) and instead of trying to go through the Gentoo update
>>> process which is difficult after that much time I decided to just do a
>>> new install. I saved copies of my kernel config and etc/make.conf but
>>> unfortunately, being primarily an x86 guy didn't think to save
>>> yaboot.conf and fstab. I've now done 5 complete Gentoo installs,
>>> starting over from scratch in case something I was doing was messing
>>> things up but so far I cannot get the machine to boot. Every time, no
>>> matter what I do at install time, I get a message
>>>
>>> "Can't check if filesystem is mounted due to a missing mtab file"
>>>
>>> A somewhat out of focus screen shot is shown here:
>>>
>>> http://www.flickr.com/photos/29328985@N03/5014227831
>>>
>>> Generally speaking I'm following the Gentoo PPC install guide located here:
>>>
>>> http://www.gentoo.org/doc/en/handbook/handbook-ppc.xml?part=1&chap=10
> <SNIP>
>
>> After looking at the screen shot, I think I have a different idea as to
>> why it might be failing and I don't think it's Yaboot.  If you've gotten
>> to init, yaboot's job is already done.
>>
>> Can you boot the install CD and chroot into the install again? When you
>> get it up and running, check to see if fsck.ext3 exists. Even if it
>> does, re-emerge e2fsprogs and see if that helps.
>> -Joe
> Very interesting. OK - I'm in the chroot now and reinstalling
> e2fsprogs as you suggest. I'll reboot in a minute and check if it
> helped. (OK - I rebooted and it didn't fix anything unfortunately. Too
> bad. Thanks for the idea though.)
>
> I was wondering if this was one of those things where device names
> were changing. They were hda all through the install, which is
> different from the Install Guide. I've tried to adjust my yaboot.conf
> file accordingly but maybe it cannot find the disk at that point
> because the name changed or something. I cannot see anything in the
> boot screen to indicate that but I suppose it's possible.
>
> While I'm here in the chroot I decided to poke around a bit. Note that
> section 9d of the install guide says that e2fsprogs is already
> installed as part of the system and indeed it appears to be as shown
> below. However I note that I cannot run updatedb for slocate without
> also getting a message about /etc/mtab not existing. Should mtab exist
> withing the chroot?
>
> (chroot) livecd / # emerge -pv e2fsprogs
>
> These are the packages that would be merged, in order:
>
> Calculating dependencies... done!
> [ebuild   R   ] sys-fs/e2fsprogs-1.41.11  USE="nls" 4,368 kB
>
> Total: 1 package (1 reinstall), Size of downloads: 4,368 kB
> (chroot) livecd / # slocate fsck.*
> slocate: fatal error: Could not find user database
> '/var/lib/slocate/slocate.db':  No such file or directory
> (chroot) livecd / # updatedb
> updatedb: fatal error: load_file: Could not open file: /etc/mtab: No
> such file or directory
> updatedb: fatal error: parse_fs_exclude: Could not load file data: /etc/mtab
> ^C
> (chroot) livecd / #
>
>
> Indeed, on a different system /etc/mtab exists:
>
> gandalf ~ # cat /etc/mtab
> /dev/sda3 / ext3 rw,noatime,commit=0 0 0
> proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0
> sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0
> udev /dev tmpfs rw,nosuid,relatime,size=10240k,mode=755 0 0
> devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620 0 0
> /dev/sda5 /home/herb ext3 rw,noatime,commit=0 0 0
> shm /dev/shm tmpfs rw,noexec,nosuid,nodev 0 0
> none /proc/fs/vmblock/mountPoint vmblock rw 0 0
> gandalf ~ #
>
> However on my MacMini it simply doesn't exist:
>
> (chroot) livecd / # ls -la /etc/mtab
> ls: cannot access /etc/mtab: No such file or directory
> (chroot) livecd / #
>
> So the question is what provides mtab? Have I missed some step in the
> install process 5 times? Man, that would be embarrassing but I'd
> gladly suffer the shame if I got the machine working! ;-)
>
> Thanks for your help. Still looking.
>
> Cheers,
> Mark
>
>

mtab is generated on boot as you mount devices. It's not the problem here.

Can you try adding this line to your yaboot config? It will make the
system boot directly into a shell instead of starting init:
### Put this in the kernel section
append="init=/bin/bash"

Once this boots, does hda* exist in /dev? How about /dev/null and /dev/zero?

-Joe

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Thu, Sep 23, 2010 at 7:10 AM, Joseph Jezak <josejx@gentoo.org> wrote:
<SNIP>
>
> mtab is generated on boot as you mount devices. It's not the problem here.
>
> Can you try adding this line to your yaboot config? It will make the
> system boot directly into a shell instead of starting init:
> ### Put this in the kernel section
> append="init=/bin/bash"
>
> Once this boots, does hda* exist in /dev? How about /dev/null and /dev/zero?
>
> -Joe

OK, so I did it like this:

boot=/dev/hda2
#device=/pci@f4000000/ata-6@d/disk@0:
device=hd:
timeout=30
install=/usr/lib/yaboot/yaboot
magicboot=/usr/lib/yaboot/ofboot

image=/boot/kernel-2.6.34-gentoo-r1
        label=Gentoo-2.6.34-r1
        append="init=/bin/bash"
        partition=4
        root=/dev/hda4
        read-only

and ran ybin -v

When I reboot I have no keyboard and cannot probe around. The screen is showing

(none) / #

The kernel boots with printk timing info on each line, and then
finishes with two messages:

bash: cannot set terminal process group (-1): Inappropriate ioctl for device
bash: no job control in this shell

and at that point the machine is hung.

So this seems like it's just not finding the hardware at this point?
No disk? No keyboard?

If you want to see the whole screen I can post another screen shot on Flickr.

Thanks for the interest and help. I'm sure we'll figure it out.

- Mark

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Joseph Jezak]

 On 09/23/10 12:17, Mark Knecht wrote:
> On Thu, Sep 23, 2010 at 7:10 AM, Joseph Jezak <josejx@gentoo.org> wrote:
> <SNIP>
>> mtab is generated on boot as you mount devices. It's not the problem here.
>>
>> Can you try adding this line to your yaboot config? It will make the
>> system boot directly into a shell instead of starting init:
>> ### Put this in the kernel section
>> append="init=/bin/bash"
>>
>> Once this boots, does hda* exist in /dev? How about /dev/null and /dev/zero?
>>
>> -Joe
> OK, so I did it like this:
>
> boot=/dev/hda2
> #device=/pci@f4000000/ata-6@d/disk@0:
> device=hd:
> timeout=30
> install=/usr/lib/yaboot/yaboot
> magicboot=/usr/lib/yaboot/ofboot
>
> image=/boot/kernel-2.6.34-gentoo-r1
>         label=Gentoo-2.6.34-r1
>         append="init=/bin/bash"
>         partition=4
>         root=/dev/hda4
>         read-only
>
> and ran ybin -v
>
> When I reboot I have no keyboard and cannot probe around. The screen is showing
>
> (none) / #
>
> The kernel boots with printk timing info on each line, and then
> finishes with two messages:
>
> bash: cannot set terminal process group (-1): Inappropriate ioctl for device
> bash: no job control in this shell
>
> and at that point the machine is hung.
>
> So this seems like it's just not finding the hardware at this point?
> No disk? No keyboard?
>
> If you want to see the whole screen I can post another screen shot on Flickr.
>
> Thanks for the interest and help. I'm sure we'll figure it out.
>
> - Mark
>
>
Okay, that all looks fine. Are you sure that you built USB keyboard
support into your kernel? This might be why it wouldn't let you type. I
wouldn't mind seeing another screen shot either. Once you get keyboard
support working, check to see if those device nodes exist.

-Joe

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Thu, Sep 23, 2010 at 1:02 PM, Joseph Jezak <josejx@gentoo.org> wrote:
>  On 09/23/10 12:17, Mark Knecht wrote:
>> On Thu, Sep 23, 2010 at 7:10 AM, Joseph Jezak <josejx@gentoo.org> wrote:
>> <SNIP>
>>> mtab is generated on boot as you mount devices. It's not the problem here.
>>>
>>> Can you try adding this line to your yaboot config? It will make the
>>> system boot directly into a shell instead of starting init:
>>> ### Put this in the kernel section
>>> append="init=/bin/bash"
>>>
>>> Once this boots, does hda* exist in /dev? How about /dev/null and /dev/zero?
>>>
>>> -Joe
>> OK, so I did it like this:
>>
>> boot=/dev/hda2
>> #device=/pci@f4000000/ata-6@d/disk@0:
>> device=hd:
>> timeout=30
>> install=/usr/lib/yaboot/yaboot
>> magicboot=/usr/lib/yaboot/ofboot
>>
>> image=/boot/kernel-2.6.34-gentoo-r1
>>         label=Gentoo-2.6.34-r1
>>         append="init=/bin/bash"
>>         partition=4
>>         root=/dev/hda4
>>         read-only
>>
>> and ran ybin -v
>>
>> When I reboot I have no keyboard and cannot probe around. The screen is showing
>>
>> (none) / #
>>
>> The kernel boots with printk timing info on each line, and then
>> finishes with two messages:
>>
>> bash: cannot set terminal process group (-1): Inappropriate ioctl for device
>> bash: no job control in this shell
>>
>> and at that point the machine is hung.
>>
>> So this seems like it's just not finding the hardware at this point?
>> No disk? No keyboard?
>>
>> If you want to see the whole screen I can post another screen shot on Flickr.
>>
>> Thanks for the interest and help. I'm sure we'll figure it out.
>>
>> - Mark
>>
>>
> Okay, that all looks fine. Are you sure that you built USB keyboard
> support into your kernel? This might be why it wouldn't let you type. I
> wouldn't mind seeing another screen shot either. Once you get keyboard
> support working, check to see if those device nodes exist.
>
> -Joe

Two pictures posted:

Top half of boot screen:
http://www.flickr.com/photos/29328985@N03/5018717650/

Bottom half of boot screen
http://www.flickr.com/photos/29328985@N03/5018718202/

Full USB HID support is built as modular. I don't seem to be able to
change it to built in. make menuconfig is only giving me modular or
not set.  (Kernel config USB info this is set is at the end)

lspci says the controller is an Apple controller and the driver is
'macio' which seems sensible. I see it in the boot screen I think.
That driver is built in, but the PATA_MACIO driver is not:

(chroot) livecd linux # cat .config | grep MACIO
# CONFIG_PATA_MACIO is not set
CONFIG_ADB_MACIO=y
(chroot) livecd linux #

Maybe I've mistakenly left the right disk driver out of the kernel
thinking the hardware was SATA based? Does the PATA_MACIO option need
to be set for the Mac Mini? I don't understand how this kernel config
would have ever worked befor unless I'm confusing where it came from.

Does the append="init=/bin/bash" command allow the kernel to load
drivers or do I need to build USBHID into the kernel to get the
keyboard to work at this level of boot?

Thanks,
Mark

(chroot) livecd linux # lspci -k
0000:00:0b.0 Host bridge: Apple Computer Inc. UniNorth 2 AGP
        Kernel driver in use: agpgart-uninorth
0000:00:10.0 VGA compatible controller: ATI Technologies Inc RV280
[Radeon 9200] (rev 01)
        Subsystem: ATI Technologies Inc RV280 [Radeon 9200]
        Kernel driver in use: radeonfb
0001:10:0b.0 Host bridge: Apple Computer Inc. UniNorth 2 PCI
0001:10:12.0 Network controller: Broadcom Corporation BCM4318
[AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
        Subsystem: Apple Computer Inc. Device 4318
0001:10:17.0 Class ff00: Apple Computer Inc. KeyLargo/Intrepid Mac I/O
        Kernel driver in use: macio
0001:10:18.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB
0001:10:19.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB
0001:10:1a.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB
        Kernel driver in use: ohci_hcd
0001:10:1b.0 USB Controller: NEC Corporation USB (rev 43)
        Subsystem: NEC Corporation Hama USB 2.0 CardBus
        Kernel driver in use: ohci_hcd
0001:10:1b.1 USB Controller: NEC Corporation USB (rev 43)
        Subsystem: NEC Corporation Hama USB 2.0 CardBus
        Kernel driver in use: ohci_hcd
0001:10:1b.2 USB Controller: NEC Corporation USB 2.0 (rev 04)
        Subsystem: NEC Corporation USB 2.0
        Kernel driver in use: ehci_hcd
0002:20:0b.0 Host bridge: Apple Computer Inc. UniNorth 2 Internal PCI
0002:20:0d.0 Class ff00: Apple Computer Inc. UniNorth/Intrepid ATA/100
        Kernel driver in use: ide-pmac
0002:20:0e.0 FireWire (IEEE 1394): Apple Computer Inc. UniNorth 2
FireWire (rev 81)
        Subsystem: Apple Computer Inc. iBook G4 2004
        Kernel driver in use: ohci1394
0002:20:0f.0 Ethernet controller: Apple Computer Inc. UniNorth 2 GMAC
(Sun GEM) (rev 80)
        Kernel driver in use: gem
(chroot) livecd linux #



(chroot) livecd linux # cat .config | grep USB | grep =
CONFIG_BT_HCIBFUSB=m
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
CONFIG_USB_NET_NET1080=m
CONFIG_USB_NET_MCS7830=m
CONFIG_USB_NET_ZAURUS=m
CONFIG_SND_USB=y
CONFIG_USB_HID=m
CONFIG_USB_HIDDEV=y
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=m
CONFIG_USB_DEVICEFS=y
CONFIG_USB_DEVICE_CLASS=y
CONFIG_USB_MON=m
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_HCD_PPC_OF=y
CONFIG_USB_OHCI_HCD=m
CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
CONFIG_USB_OHCI_HCD_PPC_OF=y
CONFIG_USB_OHCI_HCD_PCI=y
CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
CONFIG_USB_U132_HCD=m
CONFIG_USB_STORAGE=m
CONFIG_USB_STORAGE_FREECOM=m
CONFIG_USB_STORAGE_ISD200=m
CONFIG_USB_STORAGE_USBAT=m
CONFIG_USB_STORAGE_SDDR09=m
CONFIG_USB_STORAGE_SDDR55=m
CONFIG_USB_STORAGE_JUMPSHOT=m
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_AIRCABLE=m
CONFIG_USB_SERIAL_IPW=m
CONFIG_USB_SERIAL_MOS7720=m
CONFIG_USB_SERIAL_MOS7840=m
CONFIG_USB_SERIAL_SIERRAWIRELESS=m
CONFIG_USB_SERIAL_OMNINET=m
CONFIG_USB_FTDI_ELAN=m
CONFIG_USB_APPLEDISPLAY=m
(chroot) livecd linux #

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Joseph Jezak]

 My responses are inline this time. It's easier when there's so much
going on!

On 09/23/10 16:41, Mark Knecht wrote:
> Two pictures posted:
>
> Top half of boot screen:
> http://www.flickr.com/photos/29328985@N03/5018717650/
>
> Bottom half of boot screen
> http://www.flickr.com/photos/29328985@N03/5018718202/
>

Okay, these look exactly as expected. You've booted into the shell fine
and the kernel does detect the hard drive fine. It appears that the disk
was not cleanly unmounted, which is what the messages in the bottom
picture indicate. Once you get USB working so we can type into the
console, we'll take a look at what's actually going on.

> Full USB HID support is built as modular. I don't seem to be able to
> change it to built in. make menuconfig is only giving me modular or
> not set.  (Kernel config USB info this is set is at the end)
If you use menuconfig and you go to the "Help" option, it will tell you
what dependencies need to be set in order to build the module. Most
likely, you did not set the USB subsystem itself to be built in.
> lspci says the controller is an Apple controller and the driver is
> 'macio' which seems sensible. I see it in the boot screen I think.
> That driver is built in, but the PATA_MACIO driver is not:
>
> (chroot) livecd linux # cat .config | grep MACIO
> # CONFIG_PATA_MACIO is not set
> CONFIG_ADB_MACIO=y
> (chroot) livecd linux #
>
> Maybe I've mistakenly left the right disk driver out of the kernel
> thinking the hardware was SATA based? Does the PATA_MACIO option need
> to be set for the Mac Mini? I don't understand how this kernel config
> would have ever worked befor unless I'm confusing where it came from.
>

You're using the old style driver which results in devices named hdX#.
It's called IDE_PMAC. The new driver which uses the sdX# naming
convention (and uses libpata), is called PATA_MACIO.

> Does the append="init=/bin/bash" command allow the kernel to load
> drivers or do I need to build USBHID into the kernel to get the
> keyboard to work at this level of boot?

I would built it in for now, it'll be easier since there's no good way
to get into the system to tell it to load the drivers.

-Joe

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Thu, Sep 23, 2010 at 10:04 PM, Joseph Jezak <josejx@gentoo.org> wrote:
>  My responses are inline this time. It's easier when there's so much
> going on!
>
> On 09/23/10 16:41, Mark Knecht wrote:
>> Two pictures posted:
>>
>> Top half of boot screen:
>> http://www.flickr.com/photos/29328985@N03/5018717650/
>>
>> Bottom half of boot screen
>> http://www.flickr.com/photos/29328985@N03/5018718202/
>>
>
> Okay, these look exactly as expected. You've booted into the shell fine
> and the kernel does detect the hard drive fine. It appears that the disk
> was not cleanly unmounted, which is what the messages in the bottom
> picture indicate. Once you get USB working so we can type into the
> console, we'll take a look at what's actually going on.
>
>> Full USB HID support is built as modular. I don't seem to be able to
>> change it to built in. make menuconfig is only giving me modular or
>> not set.  (Kernel config USB info this is set is at the end)
> If you use menuconfig and you go to the "Help" option, it will tell you
> what dependencies need to be set in order to build the module. Most
> likely, you did not set the USB subsystem itself to be built in.
>> lspci says the controller is an Apple controller and the driver is
>> 'macio' which seems sensible. I see it in the boot screen I think.
>> That driver is built in, but the PATA_MACIO driver is not:
>>
>> (chroot) livecd linux # cat .config | grep MACIO
>> # CONFIG_PATA_MACIO is not set
>> CONFIG_ADB_MACIO=y
>> (chroot) livecd linux #
>>
>> Maybe I've mistakenly left the right disk driver out of the kernel
>> thinking the hardware was SATA based? Does the PATA_MACIO option need
>> to be set for the Mac Mini? I don't understand how this kernel config
>> would have ever worked befor unless I'm confusing where it came from.
>>
>
> You're using the old style driver which results in devices named hdX#.
> It's called IDE_PMAC. The new driver which uses the sdX# naming
> convention (and uses libpata), is called PATA_MACIO.
>
>> Does the append="init=/bin/bash" command allow the kernel to load
>> drivers or do I need to build USBHID into the kernel to get the
>> keyboard to work at this level of boot?
>
> I would built it in for now, it'll be easier since there's no good way
> to get into the system to tell it to load the drivers.
>
> -Joe
>
>

Hi Joe,
   OK - I got USB working and with the append="init=/bin/bash" in I
can at least do cd and ls commands.

   All the devices you asked about exist - /dev/hda1 through 20,
/dev/hdb1 through 20, /dev/null and /dev/zero - all exist.

   Doing know if it's a clue but in this  append="init=/bin/bash"
state I was unable to do a reboot or a shutdown as it complained about
missing initctl I think?

   Being that I made a number of changes to the kernel config to get
USB working I remove the append line from yaboot.conf and tried
booting into Gentoo proper but it's still stopping at the same place
with the same message about no mtab file.

   I'll put the append back in and wait for further ideas.

   Thanks for sticking with me!

Cheers,
Mark

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Enlightened User]

On Sep 24, 2010, at 4:30 PM, Mark Knecht wrote:

> On Thu, Sep 23, 2010 at 10:04 PM, Joseph Jezak <josejx@gentoo.org>  
> wrote:
>>  My responses are inline this time. It's easier when there's so much
>> going on!
>>
>> On 09/23/10 16:41, Mark Knecht wrote:
>>> Two pictures posted:
>>>
>>> Top half of boot screen:
>>> http://www.flickr.com/photos/29328985@N03/5018717650/
>>>
>>> Bottom half of boot screen
>>> http://www.flickr.com/photos/29328985@N03/5018718202/
>>>
>>
>> Okay, these look exactly as expected. You've booted into the shell  
>> fine
>> and the kernel does detect the hard drive fine. It appears that the  
>> disk
>> was not cleanly unmounted, which is what the messages in the bottom
>> picture indicate. Once you get USB working so we can type into the
>> console, we'll take a look at what's actually going on.
>>
>>> Full USB HID support is built as modular. I don't seem to be able to
>>> change it to built in. make menuconfig is only giving me modular or
>>> not set.  (Kernel config USB info this is set is at the end)
>> If you use menuconfig and you go to the "Help" option, it will tell  
>> you
>> what dependencies need to be set in order to build the module. Most
>> likely, you did not set the USB subsystem itself to be built in.
>>> lspci says the controller is an Apple controller and the driver is
>>> 'macio' which seems sensible. I see it in the boot screen I think.
>>> That driver is built in, but the PATA_MACIO driver is not:
>>>
>>> (chroot) livecd linux # cat .config | grep MACIO
>>> # CONFIG_PATA_MACIO is not set
>>> CONFIG_ADB_MACIO=y
>>> (chroot) livecd linux #
>>>
>>> Maybe I've mistakenly left the right disk driver out of the kernel
>>> thinking the hardware was SATA based? Does the PATA_MACIO option  
>>> need
>>> to be set for the Mac Mini? I don't understand how this kernel  
>>> config
>>> would have ever worked befor unless I'm confusing where it came  
>>> from.
>>>
>>
>> You're using the old style driver which results in devices named  
>> hdX#.
>> It's called IDE_PMAC. The new driver which uses the sdX# naming
>> convention (and uses libpata), is called PATA_MACIO.
>>
>>> Does the append="init=/bin/bash" command allow the kernel to load
>>> drivers or do I need to build USBHID into the kernel to get the
>>> keyboard to work at this level of boot?
>>
>> I would built it in for now, it'll be easier since there's no good  
>> way
>> to get into the system to tell it to load the drivers.
>>
>> -Joe
>>
>>
>
> Hi Joe,
>   OK - I got USB working and with the append="init=/bin/bash" in I
> can at least do cd and ls commands.
>
>   All the devices you asked about exist - /dev/hda1 through 20,
> /dev/hdb1 through 20, /dev/null and /dev/zero - all exist.
>
>   Doing know if it's a clue but in this  append="init=/bin/bash"
> state I was unable to do a reboot or a shutdown as it complained about
> missing initctl I think?
>
>   Being that I made a number of changes to the kernel config to get
> USB working I remove the append line from yaboot.conf and tried
> booting into Gentoo proper but it's still stopping at the same place
> with the same message about no mtab file.
>
>   I'll put the append back in and wait for further ideas.
>
>   Thanks for sticking with me!
>
> Cheers,
> Mark
>
Assuming you are still stopping near:
fsck.ext3...

Can you confirm that /sbin/fsck.ext3 exists?
If not, then emerge e2fsprogs.

Barry

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Fri, Sep 24, 2010 at 3:43 PM, Enlightened User <linux@nc.rr.com> wrote:
> On Sep 24, 2010, at 4:30 PM, Mark Knecht wrote:
>
>> On Thu, Sep 23, 2010 at 10:04 PM, Joseph Jezak <josejx@gentoo.org> wrote:
>>>
>>>  My responses are inline this time. It's easier when there's so much
>>> going on!
>>>
>>> On 09/23/10 16:41, Mark Knecht wrote:
>>>>
>>>> Two pictures posted:
>>>>
>>>> Top half of boot screen:
>>>> http://www.flickr.com/photos/29328985@N03/5018717650/
>>>>
>>>> Bottom half of boot screen
>>>> http://www.flickr.com/photos/29328985@N03/5018718202/
>>>>
>>>
>>> Okay, these look exactly as expected. You've booted into the shell fine
>>> and the kernel does detect the hard drive fine. It appears that the disk
>>> was not cleanly unmounted, which is what the messages in the bottom
>>> picture indicate. Once you get USB working so we can type into the
>>> console, we'll take a look at what's actually going on.
>>>
>>>> Full USB HID support is built as modular. I don't seem to be able to
>>>> change it to built in. make menuconfig is only giving me modular or
>>>> not set.  (Kernel config USB info this is set is at the end)
>>>
>>> If you use menuconfig and you go to the "Help" option, it will tell you
>>> what dependencies need to be set in order to build the module. Most
>>> likely, you did not set the USB subsystem itself to be built in.
>>>>
>>>> lspci says the controller is an Apple controller and the driver is
>>>> 'macio' which seems sensible. I see it in the boot screen I think.
>>>> That driver is built in, but the PATA_MACIO driver is not:
>>>>
>>>> (chroot) livecd linux # cat .config | grep MACIO
>>>> # CONFIG_PATA_MACIO is not set
>>>> CONFIG_ADB_MACIO=y
>>>> (chroot) livecd linux #
>>>>
>>>> Maybe I've mistakenly left the right disk driver out of the kernel
>>>> thinking the hardware was SATA based? Does the PATA_MACIO option need
>>>> to be set for the Mac Mini? I don't understand how this kernel config
>>>> would have ever worked befor unless I'm confusing where it came from.
>>>>
>>>
>>> You're using the old style driver which results in devices named hdX#.
>>> It's called IDE_PMAC. The new driver which uses the sdX# naming
>>> convention (and uses libpata), is called PATA_MACIO.
>>>
>>>> Does the append="init=/bin/bash" command allow the kernel to load
>>>> drivers or do I need to build USBHID into the kernel to get the
>>>> keyboard to work at this level of boot?
>>>
>>> I would built it in for now, it'll be easier since there's no good way
>>> to get into the system to tell it to load the drivers.
>>>
>>> -Joe
>>>
>>>
>>
>> Hi Joe,
>>  OK - I got USB working and with the append="init=/bin/bash" in I
>> can at least do cd and ls commands.
>>
>>  All the devices you asked about exist - /dev/hda1 through 20,
>> /dev/hdb1 through 20, /dev/null and /dev/zero - all exist.
>>
>>  Doing know if it's a clue but in this  append="init=/bin/bash"
>> state I was unable to do a reboot or a shutdown as it complained about
>> missing initctl I think?
>>
>>  Being that I made a number of changes to the kernel config to get
>> USB working I remove the append line from yaboot.conf and tried
>> booting into Gentoo proper but it's still stopping at the same place
>> with the same message about no mtab file.
>>
>>  I'll put the append back in and wait for further ideas.
>>
>>  Thanks for sticking with me!
>>
>> Cheers,
>> Mark
>>
> Assuming you are still stopping near:
> fsck.ext3...
>
> Can you confirm that /sbin/fsck.ext3 exists?
> If not, then emerge e2fsprogs.
>
> Barry
>
>

The chroot is currently doing an emerge -e @world so I've shelled into
the machine and am showing from that perspective. All the typical fsck
programs are there and I rebuilt e2fsprogs a couple of days ago.


livecd gentoo # ls /mnt/gentoo/sbin/fsck*
fsck          fsck.ext2     fsck.ext4     fsck.minix
fsck.cramfs   fsck.ext3     fsck.ext4dev
livecd gentoo #

When emerge -e @world completes I'll give it a reboot but somehow I
don't have much faith that it will have fixed anything. Right now I
feel it's either something missing from my kernel config, or some
critical install step that I keep missing because of the way I read
the document and maybe some step that listed inside a paragraph
instead of being called out in purple like most of them are. (They are
in there, like the locale-gen step and a few others...)

I'll check back later when the rebuild is complete.

Thanks!

Cheers,
Mark

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Thu, Sep 23, 2010 at 10:04 PM, Joseph Jezak <josejx@gentoo.org> wrote:
>  My responses are inline this time. It's easier when there's so much
> going on!
>
> On 09/23/10 16:41, Mark Knecht wrote:
>> Two pictures posted:
>>
>> Top half of boot screen:
>> http://www.flickr.com/photos/29328985@N03/5018717650/
>>
>> Bottom half of boot screen
>> http://www.flickr.com/photos/29328985@N03/5018718202/
>>
>
> Okay, these look exactly as expected. You've booted into the shell fine
> and the kernel does detect the hard drive fine. It appears that the disk
> was not cleanly unmounted, which is what the messages in the bottom
> picture indicate. Once you get USB working so we can type into the
> console, we'll take a look at what's actually going on.
>
>> Full USB HID support is built as modular. I don't seem to be able to
>> change it to built in. make menuconfig is only giving me modular or
>> not set.  (Kernel config USB info this is set is at the end)
> If you use menuconfig and you go to the "Help" option, it will tell you
> what dependencies need to be set in order to build the module. Most
> likely, you did not set the USB subsystem itself to be built in.
>> lspci says the controller is an Apple controller and the driver is
>> 'macio' which seems sensible. I see it in the boot screen I think.
>> That driver is built in, but the PATA_MACIO driver is not:
>>
>> (chroot) livecd linux # cat .config | grep MACIO
>> # CONFIG_PATA_MACIO is not set
>> CONFIG_ADB_MACIO=y
>> (chroot) livecd linux #
>>
>> Maybe I've mistakenly left the right disk driver out of the kernel
>> thinking the hardware was SATA based? Does the PATA_MACIO option need
>> to be set for the Mac Mini? I don't understand how this kernel config
>> would have ever worked befor unless I'm confusing where it came from.
>>
>
> You're using the old style driver which results in devices named hdX#.
> It's called IDE_PMAC. The new driver which uses the sdX# naming
> convention (and uses libpata), is called PATA_MACIO.
>
>> Does the append="init=/bin/bash" command allow the kernel to load
>> drivers or do I need to build USBHID into the kernel to get the
>> keyboard to work at this level of boot?
>
> I would built it in for now, it'll be easier since there's no good way
> to get into the system to tell it to load the drivers.
>
> -Joe
>
>

Hi Joe,
   OK, I finished the emerge -e @world. No changes. Still doesn't boot.

   I've put the append="init=/bin/bash" back in and booted. I'm at the
console and this is confusing. It seems that /dev/hda4 is probably
mounted. I can do

ls -al /

I see all the stuff I'd expect to see - /bin, /boot, etc. - and also
the two downloads necessary to do the install - portage-latest.tar.bz2
& stage3-ppc-20100919.tar.bz2 - so I must be looking at the right
physical hard drive.

However even though I see that stuff simple commands like df don't
work yielding something like this:

(none)/ #df
df: cannot read table of mounted file systems: No such file or directory

Additionally, there is nothing at all under /proc. It's empty!

Cheers,
Mark

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Joseph Jezak]

 On 09/25/10 07:45, Mark Knecht wrote:
> On Thu, Sep 23, 2010 at 10:04 PM, Joseph Jezak <josejx@gentoo.org> wrote:
>>  My responses are inline this time. It's easier when there's so much
>> going on!
>>
>> On 09/23/10 16:41, Mark Knecht wrote:
>>> Two pictures posted:
>>>
>>> Top half of boot screen:
>>> http://www.flickr.com/photos/29328985@N03/5018717650/
>>>
>>> Bottom half of boot screen
>>> http://www.flickr.com/photos/29328985@N03/5018718202/
>>>
>> Okay, these look exactly as expected. You've booted into the shell fine
>> and the kernel does detect the hard drive fine. It appears that the disk
>> was not cleanly unmounted, which is what the messages in the bottom
>> picture indicate. Once you get USB working so we can type into the
>> console, we'll take a look at what's actually going on.
>>
>>> Full USB HID support is built as modular. I don't seem to be able to
>>> change it to built in. make menuconfig is only giving me modular or
>>> not set.  (Kernel config USB info this is set is at the end)
>> If you use menuconfig and you go to the "Help" option, it will tell you
>> what dependencies need to be set in order to build the module. Most
>> likely, you did not set the USB subsystem itself to be built in.
>>> lspci says the controller is an Apple controller and the driver is
>>> 'macio' which seems sensible. I see it in the boot screen I think.
>>> That driver is built in, but the PATA_MACIO driver is not:
>>>
>>> (chroot) livecd linux # cat .config | grep MACIO
>>> # CONFIG_PATA_MACIO is not set
>>> CONFIG_ADB_MACIO=y
>>> (chroot) livecd linux #
>>>
>>> Maybe I've mistakenly left the right disk driver out of the kernel
>>> thinking the hardware was SATA based? Does the PATA_MACIO option need
>>> to be set for the Mac Mini? I don't understand how this kernel config
>>> would have ever worked befor unless I'm confusing where it came from.
>>>
>> You're using the old style driver which results in devices named hdX#.
>> It's called IDE_PMAC. The new driver which uses the sdX# naming
>> convention (and uses libpata), is called PATA_MACIO.
>>
>>> Does the append="init=/bin/bash" command allow the kernel to load
>>> drivers or do I need to build USBHID into the kernel to get the
>>> keyboard to work at this level of boot?
>> I would built it in for now, it'll be easier since there's no good way
>> to get into the system to tell it to load the drivers.
>>
>> -Joe
>>
>>
> Hi Joe,
>    OK, I finished the emerge -e @world. No changes. Still doesn't boot.
>
>    I've put the append="init=/bin/bash" back in and booted. I'm at the
> console and this is confusing. It seems that /dev/hda4 is probably
> mounted. I can do
>
> ls -al /
>
> I see all the stuff I'd expect to see - /bin, /boot, etc. - and also
> the two downloads necessary to do the install - portage-latest.tar.bz2
> & stage3-ppc-20100919.tar.bz2 - so I must be looking at the right
> physical hard drive.
>
> However even though I see that stuff simple commands like df don't
> work yielding something like this:
>
> (none)/ #df
> df: cannot read table of mounted file systems: No such file or directory
>
> Additionally, there is nothing at all under /proc. It's empty!
>
> Cheers,
> Mark
>
>
None of these things are weird, they're expected!

When you start the system with "init=/bin/bash", the only thing your
system does is start bash as the only process. Things like mounting
proc, remounting the root file system r/w (and setting up mtab) aren't
done because they're part of the normal startup process.

Can you run fsck.ext3 from the shell that starts when you replace init?

Also, which version of udev are you using? I forgot to ask if you're
running ~ppc instead of ppc, you may want to try switching to the
PATA_MACIO driver in order for the system to work properly.

-Joe

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Sat, Sep 25, 2010 at 8:12 AM, Joseph Jezak <josejx@gentoo.org> wrote:
<SNIP>
> None of these things are weird, they're expected!
>

Really? OK - cool then.

> When you start the system with "init=/bin/bash", the only thing your
> system does is start bash as the only process. Things like mounting
> proc, remounting the root file system r/w (and setting up mtab) aren't
> done because they're part of the normal startup process.
>

I need to find a good _SIMPLE_ book on how Linux boots. I'm just a
long time use with no real sys admin background so for a decade or
longer I just want the things go by at boot and then use my system.

> Can you run fsck.ext3 from the shell that starts when you replace init?
>

I cannot due to the same sort of message I get when trying to boot:

e2fsck_check_if_mount: Can't check if filesystem is mounted due to
missing mtab file
fsck.ext3: Device or resource busy while trying to open /dev/hda4
Filesystem mounted or opened exclusively by another program?

For kicks I tried umount /dev/hda4 but that complains about the
missing mtab file also. It seems from the man page I could force it
but I didn't want to do that, and again if I did and it even worked
then where would the system read fsck.ext3 from to do the check since
it's on /dev/hda4 itself?

> Also, which version of udev are you using? I forgot to ask if you're
> running ~ppc instead of ppc, you may want to try switching to the
> PATA_MACIO driver in order for the system to work properly.

udev would be whatever comes with a stable ppc system these days.

Other than running ~ppc portage and sandbox the machine is currently
all stable with no USE flags. The make.conf file is pretty much empty
other than the stuff the install has me put in. (Which mirrors to sync
from, etc.)

I've gone back and done a couple more experiments:

1) So far anything I try that refers to the drive as /dev/sda4 results
in a VFS not syncing type error so at least as far as the boot process
goes hda4 seems to be the right device.

2) I tried building in the PATA_MACIO driver but that by itself didn't
change anything:

(chroot) livecd / # cat /usr/src/linux/.config | grep MACIO
CONFIG_PATA_MACIO=y
CONFIG_ADB_MACIO=y
(chroot) livecd / #

The boot still fails at the same point with the same message. Possibly
some other ATA driver is being selected ahead of this one and maybe it
needs to be removed from the kernel? I don't know what to remove
though so I'm sort of stuck on that account.

3) If this is a kernel config issue - and it seem plausible that it is
- then I'll point out that the kernel config page of the Gentoo PPC
Istall Guide had a possible command that didn't work for me:

http://www.gentoo.org/doc/en/handbook/handbook-ppc.xml?part=1&chap=7

Specifically:

make pmac32_defconfig

which supposedly will make a config file that would boot most 32-bit
machines. Unfortunately the command doesn't work for me on current
kernels. The install guide should be updated to either remove this or
make it more clear if I need to do anything more than that command in
the /usr/src/linux directory.

I've looked around at lots more stuff in my kernel config and compared
it to what the Install guide says. I don't see any differences but I
suspect there probably are.

Thanks!

- Mark

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Sat, Sep 25, 2010 at 1:40 PM, Mark Knecht <markknecht@gmail.com> wrote:
<SNIP>
> 3) If this is a kernel config issue - and it seem plausible that it is
> - then I'll point out that the kernel config page of the Gentoo PPC
> Istall Guide had a possible command that didn't work for me:
>
> http://www.gentoo.org/doc/en/handbook/handbook-ppc.xml?part=1&chap=7
>
> Specifically:
>
> make pmac32_defconfig
>
> which supposedly will make a config file that would boot most 32-bit
> machines. Unfortunately the command doesn't work for me on current
> kernels. The install guide should be updated to either remove this or
> make it more clear if I need to do anything more than that command in
> the /usr/src/linux directory.
<SNIP>

Nix this comment. I got the command to work and am going back to
ground zero on the kernel config. We'll see what happens.

Sorry for the noise. Just frustrated after weeks of this. Mac is just
harder than PC I suppose...

Thanks,
Mark

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Sat, Sep 25, 2010 at 1:40 PM, Mark Knecht <markknecht@gmail.com> wrote:
<SNIP>
>
>> Also, which version of udev are you using? I forgot to ask if you're
>> running ~ppc instead of ppc, you may want to try switching to the
>> PATA_MACIO driver in order for the system to work properly.
>
> udev would be whatever comes with a stable ppc system these days.
>

No change at all using the kernel created by 'make pmac32_defconfig'.
Fails at the same place.

udev is version 151-r4. I haven't created any rules for it. It's all
default Gentoo.

While I'm sure I won't actually do it I feel very close to burying a
ball-peen hammer right in the middle of this little box and being done
with this mess... ;-)

 - Mark

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Joseph Jezak]

 On 09/25/10 16:40, Mark Knecht wrote:

(snip)

> I cannot due to the same sort of message I get when trying to boot:
>
> e2fsck_check_if_mount: Can't check if filesystem is mounted due to
> missing mtab file
> fsck.ext3: Device or resource busy while trying to open /dev/hda4
> Filesystem mounted or opened exclusively by another program?
>
> For kicks I tried umount /dev/hda4 but that complains about the
> missing mtab file also. It seems from the man page I could force it
> but I didn't want to do that, and again if I did and it even worked
> then where would the system read fsck.ext3 from to do the check since
> it's on /dev/hda4 itself?
>

Okay, let's try a few things now that we can boot the machine (even if
it's not all the way!).

First, lets mount proc:
# mount -t procfs none /proc

Now, try fsck.ext3 again. Does it work?

Next, let's remount the root file system read/write so we can modify files:
# mount -o remount,rw /
 
We'll copy the current mount information from proc to /etc/mtab and see
if that helps:
# cp /proc/self/mounts /etc/mtab
# mount -o remount,ro /

Now, try fsck.ext3 again. Does it work?

If so, try rebooting the system again. Does it boot now?

(snip)

> I've gone back and done a couple more experiments:
>
> 1) So far anything I try that refers to the drive as /dev/sda4 results
> in a VFS not syncing type error so at least as far as the boot process
> goes hda4 seems to be the right device.
>

hda4 will be  the right device as long as you have the old ide driver in
your kernel.

> 2) I tried building in the PATA_MACIO driver but that by itself didn't
> change anything:
>
> (chroot) livecd / # cat /usr/src/linux/.config | grep MACIO
> CONFIG_PATA_MACIO=y
> CONFIG_ADB_MACIO=y
> (chroot) livecd / #
>
> The boot still fails at the same point with the same message. Possibly
> some other ATA driver is being selected ahead of this one and maybe it
> needs to be removed from the kernel? I don't know what to remove
> though so I'm sort of stuck on that account.
>
The old PMAC_IDE driver is getting picked before the PATA_MACIO driver.
If you'd like to try the newer driver, you'll need to disable the old
one first.

-Joe

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Sun, Sep 26, 2010 at 10:36 AM, Joseph Jezak <josejx@gentoo.org> wrote:
>  On 09/25/10 16:40, Mark Knecht wrote:
<SNIP>
>
> Okay, let's try a few things now that we can boot the machine (even if
> it's not all the way!).
>
> First, lets mount proc:
> # mount -t procfs none /proc
>

OK - to me this doesn't look good:

 # mount -t procfs none /proc
mount:none has wrong device number or fs type procfs not supported

on the off chance you menat proc instead of procfs I tried it that way
and got a slightly more reasonable message:

# mount -t proc none /proc
can't create lock file /etc/mtab~1038: Read-only file system (use -n
flag to override)

> Now, try fsck.ext3 again. Does it work?
>

Worked fine. fsck.ext3 said it was clean

> Next, let's remount the root file system read/write so we can modify files:
> # mount -o remount,rw /
>
Seemed to work. Got this message:

EXT3-fs: (hda4):using internal journal

> We'll copy the current mount information from proc to /etc/mtab and see
> if that helps:
> # cp /proc/self/mounts /etc/mtab
> # mount -o remount,ro /
>
> Now, try fsck.ext3 again. Does it work?
>
> If so, try rebooting the system again. Does it boot now?
>

Didn't boot but got a little farther. Doesn't complain about mtab
anymore but still complains:

* Checking root filesystem...
fsck.ext3: No such file or directory while trying to open /dev/hda4
/dev/hda4:
The superblock could not be read......


<SNIP>

>> The boot still fails at the same point with the same message. Possibly
>> some other ATA driver is being selected ahead of this one and maybe it
>> needs to be removed from the kernel? I don't know what to remove
>> though so I'm sort of stuck on that account.
>>
> The old PMAC_IDE driver is getting picked before the PATA_MACIO driver.
> If you'd like to try the newer driver, you'll need to disable the old
> one first.

OK - I'll go back in and look at my kernel config again. Thought I'd
post these results for now.

Please remember, I'm extremely thankful for all your help and the help
of others on this frustrating little problem.

Cheers,
Mark

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Sun, Sep 26, 2010 at 1:52 PM, Mark Knecht <markknecht@gmail.com> wrote:
> On Sun, Sep 26, 2010 at 10:36 AM, Joseph Jezak <josejx@gentoo.org> wrote:
<SNIP>
>> The old PMAC_IDE driver is getting picked before the PATA_MACIO driver.
>> If you'd like to try the newer driver, you'll need to disable the old
>> one first.
>
> OK - I'll go back in and look at my kernel config again. Thought I'd
> post these results for now.
>

OK, I switched to the newer PMAC_MACIO driver built into the kernel.
Names changed but the result is the same - now it fails /dev/sda4

* Checking root filesystem...
fsck.ext3: No such file or directory while trying to open /dev/sda4
/dev/sda4:
The superblock could not be read or does not describe...

Note one interesting difference with the newer driver is that I
couldn't run fsck.ext3 until I rebuilt the kernel without all the
power management stuff. Seems that by default fsck thought we were
using the battery and deferred the check.

Possibly I could have used fsck -f but I didn't want to take any chances.

Anyway, the current state is that /dev/sda4 fails to mount. With the
newer driver and modified kernel I had no problems with your bash
instructions other than the procfs issue.

Can I go further booting the machine by hand? If booting using the
init=/sbin/bash allows me to check the disk but booting automatically
does then it seems I should be able to walk through by hand doing all
the steps until I get to the same failure point, correct? I think I'll
Google around for web pages that describe that sort of thing. Sounds
like an interesting thing to get educated on after using Linux for
more than a decade... :-)

Here's my current yaboot.conf and fstab files. Note that for now the
use of /dev/hda2 is due to using the install CD. I suppose those will
have to change to 'sd' if I ever get this machine to boot Gentoo
again. (Still hoping Klaus' comment this morning about bad drives
isn't the root cause here. The MacMini doesn't look easy to open for
disk replacements...)

Again, thanks for the ideas.

Cheers,
Mark

(chroot) livecd / # cat /etc/yaboot.conf
## yaboot.conf generated by yabootconfig 1.0.8
##
## run: "man yaboot.conf" for details. Do not make changes until you have!!
##
## For a dual-boot menu, add one or more of:
## bsd=/dev/hdaX, macos=/dev/hdaY, macosx=/dev/hdaZ

boot=/dev/hda2
#device=/pci@f4000000/ata-6@d/disk@0:
device=hd:
timeout=30
install=/usr/lib/yaboot/yaboot
magicboot=/usr/lib/yaboot/ofboot

image=/boot/kernel-2.6.34-gentoo-r1
        label=Gentoo-2.6.34-r1
        #append="init=/bin/bash"
        partition=4
        root=/dev/sda4
        read-only
(chroot) livecd / #


(chroot) livecd / # cat /etc/fstab
/dev/sda4   /            ext3    noatime              0 1
/dev/sda3   none         swap    sw                   0 0

/dev/cdrom  /mnt/cdrom   auto    noauto,user          0 0

proc        /proc        proc    defaults             0 0
shm         /dev/shm     tmpfs   nodev,nosuid,noexec  0 0
(chroot) livecd / #

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Joseph Jezak]

 Sorry, I've had a busy week and didn't have time to respond!

> OK - to me this doesn't look good:
>
>  # mount -t procfs none /proc
> mount:none has wrong device number or fs type procfs not supported

Sorry, that was my mistake, I was running from memory. :) You have the
right invocation below.

> on the off chance you menat proc instead of procfs I tried it that way
> and got a slightly more reasonable message:
>
> # mount -t proc none /proc
> can't create lock file /etc/mtab~1038: Read-only file system (use -n
> flag to override)
>
>> Now, try fsck.ext3 again. Does it work?
>>
> Worked fine. fsck.ext3 said it was clean
>

Cool, so now we know that fsck is fine.

>> Next, let's remount the root file system read/write so we can modify files:
>> # mount -o remount,rw /
>>
> Seemed to work. Got this message:
>
> EXT3-fs: (hda4):using internal journal
>
>> We'll copy the current mount information from proc to /etc/mtab and see
>> if that helps:
>> # cp /proc/self/mounts /etc/mtab
>> # mount -o remount,ro /
>>
>> Now, try fsck.ext3 again. Does it work?
>>
>> If so, try rebooting the system again. Does it boot now?
>>
> Didn't boot but got a little farther. Doesn't complain about mtab
> anymore but still complains:
>
> * Checking root filesystem...
> fsck.ext3: No such file or directory while trying to open /dev/hda4
> /dev/hda4:
> The superblock could not be read......
>
>
Okay, so we fixed the first thing. That's good. :) Can you attach your
whole kernel config? I'm wondering if maybe udev isn't running properly
due to a misconfiguration.

-Joe

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

[-- Attachment #1: Type: text/plain, Size: 614 bytes --]

On Fri, Oct 1, 2010 at 6:54 AM, Joseph Jezak <josejx@gentoo.org> wrote:
>  Sorry, I've had a busy week and didn't have time to respond!
>

Not a problem. I've been busy myself.

<SNIP>
>>> Now, try fsck.ext3 again. Does it work?
>>>
>> Worked fine. fsck.ext3 said it was clean
>>
>
> Cool, so now we know that fsck is fine.
>

Good.

<SNIP>
> Okay, so we fixed the first thing. That's good. :) Can you attach your
> whole kernel config? I'm wondering if maybe udev isn't running properly
> due to a misconfiguration.
>
> -Joe

Attached unless GMail does something to it.

Thanks,
Mark

[-- Attachment #2: 2.6.34-gentoo-r5.config --]
[-- Type: application/octet-stream, Size: 57074 bytes --]

#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.34-gentoo-r1
# Fri Oct  1 09:52:17 2010
#
# CONFIG_PPC64 is not set

#
# Processor support
#
CONFIG_PPC_BOOK3S_32=y
# CONFIG_PPC_85xx is not set
# CONFIG_PPC_8xx is not set
# CONFIG_40x is not set
# CONFIG_44x is not set
# CONFIG_E200 is not set
CONFIG_PPC_BOOK3S=y
CONFIG_6xx=y
CONFIG_PPC_FPU=y
CONFIG_ALTIVEC=y
CONFIG_PPC_STD_MMU=y
CONFIG_PPC_STD_MMU_32=y
# CONFIG_PPC_MM_SLICES is not set
CONFIG_PPC_HAVE_PMU_SUPPORT=y
CONFIG_PPC_PERF_CTRS=y
# CONFIG_SMP is not set
CONFIG_PPC32=y
CONFIG_WORD_SIZE=32
# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
CONFIG_MMU=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
# CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK is not set
CONFIG_IRQ_PER_CPU=y
CONFIG_NR_IRQS=512
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_ARCH_HAS_ILOG2_U32=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
CONFIG_PPC=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_NVRAM=y
CONFIG_SCHED_OMIT_FRAME_POINTER=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_PPC_OF=y
CONFIG_OF=y
# CONFIG_PPC_UDBG_16550 is not set
# CONFIG_GENERIC_TBSYNC is not set
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_DTC=y
# CONFIG_DEFAULT_UIMAGE is not set
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
# CONFIG_PPC_DCR_NATIVE is not set
# CONFIG_PPC_DCR_MMIO is not set
CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_CONSTRUCTORS=y

#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_POSIX_MQUEUE_SYSCTL=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set

#
# RCU Subsystem
#
CONFIG_TREE_RCU=y
# CONFIG_TREE_PREEMPT_RCU is not set
# CONFIG_TINY_RCU is not set
# CONFIG_RCU_TRACE is not set
CONFIG_RCU_FANOUT=32
# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_CGROUPS is not set
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
CONFIG_NAMESPACES=y
# CONFIG_UTS_NS is not set
# CONFIG_IPC_NS is not set
# CONFIG_USER_NS is not set
# CONFIG_PID_NS is not set
# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_RD_GZIP=y
CONFIG_RD_BZIP2=y
CONFIG_RD_LZMA=y
CONFIG_RD_LZO=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
# CONFIG_EMBEDDED is not set
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
CONFIG_HAVE_PERF_EVENTS=y

#
# Kernel Performance Events And Counters
#
CONFIG_PERF_EVENTS=y
# CONFIG_PERF_COUNTERS is not set
# CONFIG_DEBUG_PERF_USE_VMALLOC is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
CONFIG_SLUB_DEBUG=y
# CONFIG_COMPAT_BRK is not set
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_HAVE_DMA_API_DEBUG=y

#
# GCOV-based kernel profiling
#
# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
CONFIG_LBDAF=y
CONFIG_BLK_DEV_BSG=y
# CONFIG_BLK_DEV_INTEGRITY is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
# CONFIG_INLINE_SPIN_TRYLOCK is not set
# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
# CONFIG_INLINE_SPIN_LOCK is not set
# CONFIG_INLINE_SPIN_LOCK_BH is not set
# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
# CONFIG_INLINE_SPIN_UNLOCK is not set
# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
# CONFIG_INLINE_SPIN_UNLOCK_IRQ is not set
# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
# CONFIG_INLINE_READ_TRYLOCK is not set
# CONFIG_INLINE_READ_LOCK is not set
# CONFIG_INLINE_READ_LOCK_BH is not set
# CONFIG_INLINE_READ_LOCK_IRQ is not set
# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
# CONFIG_INLINE_READ_UNLOCK is not set
# CONFIG_INLINE_READ_UNLOCK_BH is not set
# CONFIG_INLINE_READ_UNLOCK_IRQ is not set
# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
# CONFIG_INLINE_WRITE_TRYLOCK is not set
# CONFIG_INLINE_WRITE_LOCK is not set
# CONFIG_INLINE_WRITE_LOCK_BH is not set
# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
# CONFIG_INLINE_WRITE_UNLOCK is not set
# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
# CONFIG_INLINE_WRITE_UNLOCK_IRQ is not set
# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
# CONFIG_MUTEX_SPIN_ON_OWNER is not set
CONFIG_FREEZER=y

#
# Platform support
#
# CONFIG_PPC_CHRP is not set
# CONFIG_MPC5121_ADS is not set
# CONFIG_MPC5121_GENERIC is not set
# CONFIG_PPC_MPC52xx is not set
CONFIG_PPC_PMAC=y
# CONFIG_PPC_CELL is not set
# CONFIG_PPC_CELL_NATIVE is not set
# CONFIG_PPC_82xx is not set
# CONFIG_PQ2ADS is not set
# CONFIG_PPC_83xx is not set
# CONFIG_PPC_86xx is not set
# CONFIG_EMBEDDED6xx is not set
# CONFIG_AMIGAONE is not set
CONFIG_PPC_NATIVE=y
CONFIG_PPC_OF_BOOT_TRAMPOLINE=y
# CONFIG_IPIC is not set
CONFIG_MPIC=y
# CONFIG_MPIC_WEIRD is not set
# CONFIG_PPC_I8259 is not set
# CONFIG_PPC_RTAS is not set
# CONFIG_MMIO_NVRAM is not set
CONFIG_PPC_MPC106=y
# CONFIG_PPC_970_NAP is not set
# CONFIG_PPC_INDIRECT_IO is not set
# CONFIG_GENERIC_IOMAP is not set
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=y
# CONFIG_CPU_FREQ_STAT_DETAILS is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
# CONFIG_CPU_FREQ_GOV_ONDEMAND is not set
# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set

#
# CPU Frequency drivers
#
CONFIG_CPU_FREQ_PMAC=y
CONFIG_PPC601_SYNC_FIX=y
# CONFIG_TAU is not set
# CONFIG_FSL_ULI1575 is not set
# CONFIG_SIMPLE_GPIO is not set

#
# Kernel options
#
CONFIG_HIGHMEM=y
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
# CONFIG_HZ_300 is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
CONFIG_SCHED_HRTICK=y
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_BINFMT_ELF=y
# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
# CONFIG_HAVE_AOUT is not set
CONFIG_BINFMT_MISC=m
# CONFIG_IOMMU_HELPER is not set
# CONFIG_SWIOTLB is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_ARCH_HAS_WALK_MEMORY=y
CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_SPARSE_IRQ=y
CONFIG_MAX_ACTIVE_REGIONS=32
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_MIGRATION is not set
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_VIRT_TO_BUS=y
# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_PPC_4K_PAGES=y
# CONFIG_PPC_16K_PAGES is not set
# CONFIG_PPC_64K_PAGES is not set
# CONFIG_PPC_256K_PAGES is not set
CONFIG_FORCE_MAX_ZONEORDER=11
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
CONFIG_EXTRA_TARGETS=""
CONFIG_ARCH_WANTS_FREEZER_CONTROL=y
CONFIG_PM=y
CONFIG_PM_DEBUG=y
# CONFIG_PM_ADVANCED_DEBUG is not set
# CONFIG_PM_VERBOSE is not set
CONFIG_CAN_PM_TRACE=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
CONFIG_HIBERNATION_NVS=y
CONFIG_HIBERNATION=y
CONFIG_PM_STD_PARTITION=""
CONFIG_APM_EMULATION=y
# CONFIG_PM_RUNTIME is not set
CONFIG_PM_OPS=y
CONFIG_SECCOMP=y
CONFIG_ISA_DMA_API=y

#
# Bus options
#
CONFIG_ZONE_DMA=y
# CONFIG_NEED_DMA_MAP_STATE is not set
CONFIG_GENERIC_ISA_DMA=y
CONFIG_PPC_INDIRECT_PCI=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCI_SYSCALL=y
# CONFIG_PCIEPORTBUS is not set
CONFIG_ARCH_SUPPORTS_MSI=y
# CONFIG_PCI_MSI is not set
# CONFIG_PCI_DEBUG is not set
# CONFIG_PCI_STUB is not set
# CONFIG_PCI_IOV is not set
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
# CONFIG_HAS_RAPIDIO is not set

#
# Advanced setup
#
# CONFIG_ADVANCED_OPTIONS is not set

#
# Default settings for advanced configuration options are used
#
CONFIG_LOWMEM_SIZE=0x30000000
CONFIG_PAGE_OFFSET=0xc0000000
CONFIG_KERNEL_START=0xc0000000
CONFIG_PHYSICAL_START=0x00000000
CONFIG_TASK_SIZE=0xc0000000
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=y
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
# CONFIG_XFRM_STATISTICS is not set
CONFIG_NET_KEY=y
# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=y
CONFIG_INET_ESP=y
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
# CONFIG_INET_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
CONFIG_INET_XFRM_MODE_BEET=y
# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
# CONFIG_NETWORK_SECMARK is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_NETFILTER_ADVANCED=y

#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_NETLINK=m
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
CONFIG_NF_CONNTRACK=m
# CONFIG_NF_CT_ACCT is not set
# CONFIG_NF_CONNTRACK_MARK is not set
# CONFIG_NF_CONNTRACK_EVENTS is not set
CONFIG_NF_CT_PROTO_DCCP=m
# CONFIG_NF_CT_PROTO_SCTP is not set
# CONFIG_NF_CT_PROTO_UDPLITE is not set
# CONFIG_NF_CONNTRACK_AMANDA is not set
CONFIG_NF_CONNTRACK_FTP=m
# CONFIG_NF_CONNTRACK_H323 is not set
CONFIG_NF_CONNTRACK_IRC=m
# CONFIG_NF_CONNTRACK_NETBIOS_NS is not set
# CONFIG_NF_CONNTRACK_PPTP is not set
# CONFIG_NF_CONNTRACK_SANE is not set
# CONFIG_NF_CONNTRACK_SIP is not set
CONFIG_NF_CONNTRACK_TFTP=m
CONFIG_NF_CT_NETLINK=m
# CONFIG_NETFILTER_TPROXY is not set
CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
# CONFIG_NETFILTER_XT_TARGET_CONNMARK is not set
# CONFIG_NETFILTER_XT_TARGET_CT is not set
# CONFIG_NETFILTER_XT_TARGET_DSCP is not set
CONFIG_NETFILTER_XT_TARGET_HL=m
# CONFIG_NETFILTER_XT_TARGET_LED is not set
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
CONFIG_NETFILTER_XT_TARGET_RATEEST=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
# CONFIG_NETFILTER_XT_MATCH_CLUSTER is not set
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
# CONFIG_NETFILTER_XT_MATCH_CONNBYTES is not set
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
# CONFIG_NETFILTER_XT_MATCH_CONNMARK is not set
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
CONFIG_NETFILTER_XT_MATCH_DCCP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set
CONFIG_NETFILTER_XT_MATCH_HELPER=m
CONFIG_NETFILTER_XT_MATCH_HL=m
CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
# CONFIG_NETFILTER_XT_MATCH_QUOTA is not set
CONFIG_NETFILTER_XT_MATCH_RATEEST=m
CONFIG_NETFILTER_XT_MATCH_REALM=m
CONFIG_NETFILTER_XT_MATCH_RECENT=m
# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set
CONFIG_NETFILTER_XT_MATCH_SCTP=m
# CONFIG_NETFILTER_XT_MATCH_STATE is not set
# CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set
CONFIG_NETFILTER_XT_MATCH_STRING=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
# CONFIG_NETFILTER_XT_MATCH_OSF is not set
# CONFIG_IP_VS is not set

#
# IP: Netfilter Configuration
#
CONFIG_NF_DEFRAG_IPV4=m
CONFIG_NF_CONNTRACK_IPV4=m
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
# CONFIG_IP_NF_QUEUE is not set
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_NF_NAT=m
CONFIG_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
# CONFIG_NF_NAT_SNMP_BASIC is not set
CONFIG_NF_NAT_PROTO_DCCP=m
CONFIG_NF_NAT_FTP=m
CONFIG_NF_NAT_IRC=m
CONFIG_NF_NAT_TFTP=m
# CONFIG_NF_NAT_AMANDA is not set
# CONFIG_NF_NAT_PPTP is not set
# CONFIG_NF_NAT_H323 is not set
# CONFIG_NF_NAT_SIP is not set
CONFIG_IP_NF_MANGLE=m
# CONFIG_IP_NF_TARGET_CLUSTERIP is not set
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_TTL=m
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_IP_DCCP=m
CONFIG_INET_DCCP_DIAG=m

#
# DCCP CCIDs Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP_CCID2_DEBUG is not set
CONFIG_IP_DCCP_CCID3=y
# CONFIG_IP_DCCP_CCID3_DEBUG is not set
CONFIG_IP_DCCP_CCID3_RTO=100
CONFIG_IP_DCCP_TFRC_LIB=y

#
# DCCP Kernel Hacking
#
# CONFIG_IP_DCCP_DEBUG is not set
# CONFIG_IP_SCTP is not set
# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_NET_DSA is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_PHONET is not set
# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
CONFIG_NET_CLS_ROUTE=y
# CONFIG_DCB is not set

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
CONFIG_IRDA=m

#
# IrDA protocols
#
CONFIG_IRLAN=m
CONFIG_IRCOMM=m
# CONFIG_IRDA_ULTRA is not set

#
# IrDA options
#
CONFIG_IRDA_CACHE_LAST_LSAP=y
CONFIG_IRDA_FAST_RR=y
# CONFIG_IRDA_DEBUG is not set

#
# Infrared-port device drivers
#

#
# SIR device drivers
#
CONFIG_IRTTY_SIR=m

#
# Dongle support
#
# CONFIG_DONGLE is not set
# CONFIG_KINGSUN_DONGLE is not set
# CONFIG_KSDAZZLE_DONGLE is not set
# CONFIG_KS959_DONGLE is not set

#
# FIR device drivers
#
# CONFIG_USB_IRDA is not set
# CONFIG_SIGMATEL_FIR is not set
# CONFIG_NSC_FIR is not set
# CONFIG_WINBOND_FIR is not set
# CONFIG_TOSHIBA_FIR is not set
# CONFIG_SMC_IRCC_FIR is not set
# CONFIG_ALI_FIR is not set
# CONFIG_VLSI_FIR is not set
# CONFIG_VIA_FIR is not set
# CONFIG_MCS_FIR is not set
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_HIDP=m

#
# Bluetooth device drivers
#
# CONFIG_BT_HCIBTUSB is not set
# CONFIG_BT_HCIUART is not set
CONFIG_BT_HCIBCM203X=m
# CONFIG_BT_HCIBPA10X is not set
CONFIG_BT_HCIBFUSB=m
# CONFIG_BT_HCIVHCI is not set
# CONFIG_BT_MRVL is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
CONFIG_WEXT_CORE=y
CONFIG_WEXT_PROC=y
CONFIG_CFG80211=m
# CONFIG_NL80211_TESTMODE is not set
# CONFIG_CFG80211_DEVELOPER_WARNINGS is not set
# CONFIG_CFG80211_REG_DEBUG is not set
CONFIG_CFG80211_DEFAULT_PS=y
# CONFIG_CFG80211_DEBUGFS is not set
# CONFIG_CFG80211_INTERNAL_REGDB is not set
CONFIG_CFG80211_WEXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
# CONFIG_LIB80211 is not set
CONFIG_MAC80211=m
CONFIG_MAC80211_RC_MINSTREL=y
# CONFIG_MAC80211_RC_DEFAULT_PID is not set
CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
CONFIG_MAC80211_RC_DEFAULT="minstrel"
# CONFIG_MAC80211_MESH is not set
CONFIG_MAC80211_LEDS=y
# CONFIG_MAC80211_DEBUGFS is not set
# CONFIG_MAC80211_DEBUG_MENU is not set
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
# CONFIG_DEVTMPFS is not set
# CONFIG_STANDALONE is not set
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
CONFIG_FIRMWARE_IN_KERNEL=y
CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=y
CONFIG_PROC_EVENTS=y
# CONFIG_MTD is not set
CONFIG_OF_FLATTREE=y
CONFIG_OF_DYNAMIC=y
CONFIG_OF_DEVICE=y
CONFIG_OF_I2C=y
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_FD is not set
CONFIG_MAC_FLOPPY=m
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_DRBD is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
CONFIG_BLK_DEV_UB=m
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_AD525X_DPOT is not set
# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_HP_ILO is not set
# CONFIG_ISL29003 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_DS1682 is not set
# CONFIG_C2PORT is not set

#
# EEPROM support
#
# CONFIG_EEPROM_AT24 is not set
# CONFIG_EEPROM_LEGACY is not set
# CONFIG_EEPROM_MAX6875 is not set
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_CB710_CORE is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set

#
# SCSI device support
#
CONFIG_SCSI_MOD=y
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
CONFIG_SCSI_NETLINK=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=y
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
CONFIG_SCSI_WAIT_SCAN=m

#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=y
CONFIG_SCSI_FC_ATTRS=y
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_BE2ISCSI is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_HPSA is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_3W_SAS is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
CONFIG_SCSI_AIC7XXX=m
CONFIG_AIC7XXX_CMDS_PER_DEVICE=253
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
CONFIG_AIC7XXX_DEBUG_ENABLE=y
CONFIG_AIC7XXX_DEBUG_MASK=0
CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
CONFIG_SCSI_AIC7XXX_OLD=m
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_MPT2SAS is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_FCOE is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_STEX is not set
CONFIG_SCSI_SYM53C8XX_2=y
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=0
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
CONFIG_SCSI_SYM53C8XX_MMIO=y
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
CONFIG_SCSI_MESH=y
CONFIG_SCSI_MESH_SYNC_RATE=5
CONFIG_SCSI_MESH_RESET_DELAY_MS=4000
CONFIG_SCSI_MAC53C94=y
# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_PM8001 is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_BFA_FC is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SIL24 is not set
CONFIG_ATA_SFF=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_NV is not set
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_LEGACY is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_TOSHIBA is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
# CONFIG_PATA_PLATFORM is not set
# CONFIG_PATA_SCH is not set
CONFIG_PATA_MACIO=y
# CONFIG_MD is not set
# CONFIG_FUSION is not set

#
# IEEE 1394 (FireWire) support
#

#
# You can enable one or both FireWire driver stacks.
#

#
# The newer stack is recommended.
#
# CONFIG_FIREWIRE is not set
CONFIG_IEEE1394=m
CONFIG_IEEE1394_OHCI1394=m
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_SBP2=m
# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set
# CONFIG_IEEE1394_ETH1394_ROM_ENTRY is not set
# CONFIG_IEEE1394_ETH1394 is not set
CONFIG_IEEE1394_RAWIO=m
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_DV1394=m
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_I2O is not set
CONFIG_MACINTOSH_DRIVERS=y
CONFIG_ADB=y
CONFIG_ADB_CUDA=y
CONFIG_ADB_PMU=y
CONFIG_ADB_PMU_LED=y
CONFIG_ADB_PMU_LED_IDE=y
CONFIG_PMAC_APM_EMU=m
# CONFIG_PMAC_MEDIABAY is not set
# CONFIG_PMAC_BACKLIGHT is not set
CONFIG_INPUT_ADBHID=y
CONFIG_MAC_EMUMOUSEBTN=y
CONFIG_THERM_WINDTUNNEL=m
CONFIG_THERM_ADT746X=m
# CONFIG_WINDFARM is not set
# CONFIG_ANSLCD is not set
# CONFIG_PMAC_RACKMETER is not set
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
# CONFIG_VETH is not set
# CONFIG_ARCNET is not set
# CONFIG_PHYLIB is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
CONFIG_MACE=y
# CONFIG_MACE_AAUI_PORT is not set
CONFIG_BMAC=y
# CONFIG_HAPPYMEAL is not set
CONFIG_SUNGEM=y
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_ETHOC is not set
# CONFIG_DNET is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
CONFIG_NET_PCI=y
CONFIG_PCNET32=y
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_KSZ884X_PCI is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_R6040 is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SMSC9420 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_KS8842 is not set
# CONFIG_KS8851_MLL is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
# CONFIG_ATL2 is not set
# CONFIG_XILINX_EMACLITE is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
# CONFIG_WLAN is not set

#
# Enable WiMAX (Networking options) to see the WiMAX drivers
#

#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
# CONFIG_USB_NET_CDC_EEM is not set
# CONFIG_USB_NET_DM9601 is not set
# CONFIG_USB_NET_SMSC75XX is not set
# CONFIG_USB_NET_SMSC95XX is not set
# CONFIG_USB_NET_GL620A is not set
CONFIG_USB_NET_NET1080=m
# CONFIG_USB_NET_PLUSB is not set
# CONFIG_USB_NET_MCS7830 is not set
# CONFIG_USB_NET_RNDIS_HOST is not set
# CONFIG_USB_NET_CDC_SUBSET is not set
CONFIG_USB_NET_ZAURUS=m
# CONFIG_USB_NET_INT51X1 is not set
# CONFIG_USB_IPHETH is not set
# CONFIG_USB_SIERRA_NET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_VMXNET3 is not set
# CONFIG_ISDN is not set
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set
# CONFIG_INPUT_SPARSEKMAP is not set

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_ADP5588 is not set
# CONFIG_KEYBOARD_ATKBD is not set
# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_LM8323 is not set
# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
CONFIG_MOUSE_APPLETOUCH=y
# CONFIG_MOUSE_BCM5974 is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_MOUSE_SYNAPTICS_I2C is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set

#
# Hardware I/O ports
#
CONFIG_SERIO=y
# CONFIG_SERIO_I8042 is not set
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_PCIPS2 is not set
# CONFIG_SERIO_RAW is not set
# CONFIG_SERIO_XILINX_XPS_PS2 is not set
# CONFIG_SERIO_ALTERA_PS2 is not set
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_NOZOMI is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=m
CONFIG_SERIAL_8250_PCI=m
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
# CONFIG_SERIAL_UARTLITE is not set
CONFIG_SERIAL_CORE=m
CONFIG_SERIAL_PMACZILOG=m
CONFIG_SERIAL_PMACZILOG_TTYS=y
# CONFIG_SERIAL_JSM is not set
# CONFIG_SERIAL_OF_PLATFORM is not set
# CONFIG_SERIAL_TIMBERDALE is not set
# CONFIG_SERIAL_GRLIB_GAISLER_APBUART is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_HVC_UDBG is not set
# CONFIG_IPMI_HANDLER is not set
CONFIG_HW_RANDOM=m
# CONFIG_HW_RANDOM_TIMERIOMEM is not set
CONFIG_NVRAM=y
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=m
CONFIG_I2C_HELPER_AUTO=y
CONFIG_I2C_ALGOBIT=y

#
# I2C Hardware Bus support
#

#
# PC SMBus host controller drivers
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_ISCH is not set
# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set

#
# Mac SMBus host controller drivers
#
CONFIG_I2C_POWERMAC=y

#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
# CONFIG_I2C_MPC is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_XILINX is not set

#
# External I2C/SMBus adapter drivers
#
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_TAOS_EVM is not set
# CONFIG_I2C_TINY_USB is not set

#
# Other I2C/SMBus bus drivers
#
# CONFIG_I2C_PCA_PLATFORM is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_SPI is not set

#
# PPS support
#
# CONFIG_PPS is not set
CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
# CONFIG_GPIOLIB is not set
# CONFIG_W1 is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_APM_POWER is not set
# CONFIG_BATTERY_DS2760 is not set
# CONFIG_BATTERY_DS2782 is not set
# CONFIG_BATTERY_PMU is not set
# CONFIG_BATTERY_BQ27x00 is not set
# CONFIG_BATTERY_MAX17040 is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y

#
# Sonics Silicon Backplane
#
CONFIG_SSB=m
CONFIG_SSB_SPROM=y
CONFIG_SSB_PCIHOST_POSSIBLE=y
CONFIG_SSB_PCIHOST=y
# CONFIG_SSB_B43_PCI_BRIDGE is not set
# CONFIG_SSB_DEBUG is not set
CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
CONFIG_SSB_DRIVER_PCICORE=y

#
# Multifunction device drivers
#
# CONFIG_MFD_CORE is not set
# CONFIG_MFD_88PM860X is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_TWL4030_CORE is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_PMIC_ADP5520 is not set
# CONFIG_MFD_MAX8925 is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_WM8994 is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_AB3100_CORE is not set
# CONFIG_LPC_SCH is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set

#
# Graphics support
#
CONFIG_AGP=m
CONFIG_AGP_UNINORTH=m
CONFIG_VGA_ARB=y
CONFIG_VGA_ARB_MAX_GPUS=16
CONFIG_DRM=m
CONFIG_DRM_KMS_HELPER=m
CONFIG_DRM_TTM=m
# CONFIG_DRM_TDFX is not set
CONFIG_DRM_R128=m
CONFIG_DRM_RADEON=m
# CONFIG_DRM_RADEON_KMS is not set
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
# CONFIG_DRM_VIA is not set
# CONFIG_DRM_SAVAGE is not set
CONFIG_VGASTATE=y
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
CONFIG_FB=y
# CONFIG_FIRMWARE_EDID is not set
CONFIG_FB_DDC=y
# CONFIG_FB_BOOT_VESA_SUPPORT is not set
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
# CONFIG_FB_SVGALIB is not set
CONFIG_FB_MACMODES=y
CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y

#
# Frame buffer hardware drivers
#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
CONFIG_FB_OF=y
CONFIG_FB_CONTROL=y
CONFIG_FB_PLATINUM=y
CONFIG_FB_VALKYRIE=y
CONFIG_FB_CT65550=y
# CONFIG_FB_ASILIANT is not set
CONFIG_FB_IMSTT=y
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_UVESA is not set
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_NVIDIA=y
CONFIG_FB_NVIDIA_I2C=y
# CONFIG_FB_NVIDIA_DEBUG is not set
CONFIG_FB_NVIDIA_BACKLIGHT=y
# CONFIG_FB_RIVA is not set
CONFIG_FB_MATROX=y
CONFIG_FB_MATROX_MILLENIUM=y
CONFIG_FB_MATROX_MYSTIQUE=y
# CONFIG_FB_MATROX_G is not set
# CONFIG_FB_MATROX_I2C is not set
CONFIG_FB_RADEON=y
CONFIG_FB_RADEON_I2C=y
CONFIG_FB_RADEON_BACKLIGHT=y
# CONFIG_FB_RADEON_DEBUG is not set
CONFIG_FB_ATY128=y
CONFIG_FB_ATY128_BACKLIGHT=y
CONFIG_FB_ATY=y
CONFIG_FB_ATY_CT=y
# CONFIG_FB_ATY_GENERIC_LCD is not set
CONFIG_FB_ATY_GX=y
CONFIG_FB_ATY_BACKLIGHT=y
# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_VIA is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
CONFIG_FB_3DFX=y
# CONFIG_FB_3DFX_ACCEL is not set
CONFIG_FB_3DFX_I2C=y
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_CARMINE is not set
# CONFIG_FB_IBM_GXT4500 is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FB_METRONOME is not set
# CONFIG_FB_MB862XX is not set
# CONFIG_FB_BROADSHEET is not set
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=m
# CONFIG_LCD_ILI9320 is not set
# CONFIG_LCD_PLATFORM is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
CONFIG_BACKLIGHT_GENERIC=y

#
# Display device support
#
CONFIG_DISPLAY_SUPPORT=y

#
# Display hardware drivers
#

#
# Console display driver support
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_SOUND=m
CONFIG_SOUND_OSS_CORE=y
CONFIG_SOUND_OSS_CORE_PRECLAIM=y
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
# CONFIG_SND_HRTIMER is not set
# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
CONFIG_SND_VMASTER=y
CONFIG_SND_RAWMIDI_SEQ=m
# CONFIG_SND_OPL3_LIB_SEQ is not set
# CONFIG_SND_OPL4_LIB_SEQ is not set
# CONFIG_SND_SBAWE_SEQ is not set
# CONFIG_SND_EMU10K1_SEQ is not set
CONFIG_SND_DRIVERS=y
CONFIG_SND_DUMMY=m
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
CONFIG_SND_PCI=y
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AW2 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_OXYGEN is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS5530 is not set
# CONFIG_SND_CS5535AUDIO is not set
# CONFIG_SND_CTXFI is not set
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
# CONFIG_SND_INDIGOIOX is not set
# CONFIG_SND_INDIGODJX is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_HDA_INTEL is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_HIFIER is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_LX6464ES is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VIRTUOSO is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
CONFIG_SND_PPC=y
CONFIG_SND_POWERMAC=m
CONFIG_SND_POWERMAC_AUTO_DRC=y
CONFIG_SND_AOA=m
CONFIG_SND_AOA_FABRIC_LAYOUT=m
CONFIG_SND_AOA_ONYX=m
CONFIG_SND_AOA_TAS=m
CONFIG_SND_AOA_TOONIE=m
CONFIG_SND_AOA_SOUNDBUS=m
CONFIG_SND_AOA_SOUNDBUS_I2S=m
CONFIG_SND_USB=y
CONFIG_SND_USB_AUDIO=m
# CONFIG_SND_USB_UA101 is not set
# CONFIG_SND_USB_USX2Y is not set
# CONFIG_SND_USB_CAIAQ is not set
# CONFIG_SND_SOC is not set
# CONFIG_SOUND_PRIME is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HIDRAW is not set

#
# USB Input Devices
#
CONFIG_USB_HID=y
# CONFIG_HID_PID is not set
# CONFIG_USB_HIDDEV is not set

#
# Special HID drivers
#
# CONFIG_HID_3M_PCT is not set
CONFIG_HID_A4TECH=y
CONFIG_HID_APPLE=y
CONFIG_HID_BELKIN=y
CONFIG_HID_CHERRY=y
CONFIG_HID_CHICONY=y
CONFIG_HID_CYPRESS=y
CONFIG_HID_DRAGONRISE=y
# CONFIG_DRAGONRISE_FF is not set
CONFIG_HID_EZKEY=y
CONFIG_HID_KYE=y
CONFIG_HID_GYRATION=y
CONFIG_HID_TWINHAN=y
CONFIG_HID_KENSINGTON=y
CONFIG_HID_LOGITECH=y
# CONFIG_LOGITECH_FF is not set
# CONFIG_LOGIRUMBLEPAD2_FF is not set
# CONFIG_LOGIG940_FF is not set
# CONFIG_HID_MAGICMOUSE is not set
CONFIG_HID_MICROSOFT=y
# CONFIG_HID_MOSART is not set
CONFIG_HID_MONTEREY=y
CONFIG_HID_NTRIG=y
CONFIG_HID_ORTEK=y
CONFIG_HID_PANTHERLORD=y
# CONFIG_PANTHERLORD_FF is not set
CONFIG_HID_PETALYNX=y
# CONFIG_HID_QUANTA is not set
CONFIG_HID_SAMSUNG=y
CONFIG_HID_SONY=y
# CONFIG_HID_STANTUM is not set
CONFIG_HID_SUNPLUS=y
CONFIG_HID_GREENASIA=y
# CONFIG_GREENASIA_FF is not set
CONFIG_HID_SMARTJOYPLUS=y
# CONFIG_SMARTJOYPLUS_FF is not set
CONFIG_HID_TOPSEED=y
CONFIG_HID_THRUSTMASTER=y
# CONFIG_THRUSTMASTER_FF is not set
# CONFIG_HID_WACOM is not set
CONFIG_HID_ZEROPLUS=y
# CONFIG_ZEROPLUS_FF is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_DEVICE_CLASS=y
CONFIG_USB_DYNAMIC_MINORS=y
CONFIG_USB_MON=y
# CONFIG_USB_WUSB is not set
# CONFIG_USB_WUSB_CBAF is not set

#
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
# CONFIG_USB_XHCI_HCD is not set
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_XPS_USB_HCD_XILINX is not set
# CONFIG_USB_EHCI_HCD_PPC_OF is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_HCD_PPC_OF_BE is not set
# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
# CONFIG_USB_OHCI_HCD_PPC_OF is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_WHCI_HCD is not set
# CONFIG_USB_HWA_HCD is not set

#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
# CONFIG_USB_WDM is not set
# CONFIG_USB_TMC is not set

#
# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#

#
# also be needed; see USB_STORAGE Help for more info
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
CONFIG_USB_STORAGE_ONETOUCH=m
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_LIBUSUAL is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set

#
# USB port drivers
#
CONFIG_USB_SERIAL=m
CONFIG_USB_EZUSB=y
# CONFIG_USB_SERIAL_GENERIC is not set
# CONFIG_USB_SERIAL_AIRCABLE is not set
# CONFIG_USB_SERIAL_ARK3116 is not set
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_CH341 is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_CP210X is not set
# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
# CONFIG_USB_SERIAL_FUNSOFT is not set
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
# CONFIG_USB_SERIAL_IR is not set
# CONFIG_USB_SERIAL_EDGEPORT is not set
# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
# CONFIG_USB_SERIAL_GARMIN is not set
# CONFIG_USB_SERIAL_IPW is not set
# CONFIG_USB_SERIAL_IUU is not set
CONFIG_USB_SERIAL_KEYSPAN_PDA=m
CONFIG_USB_SERIAL_KEYSPAN=m
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
# CONFIG_USB_SERIAL_MOS7720 is not set
# CONFIG_USB_SERIAL_MOS7840 is not set
# CONFIG_USB_SERIAL_MOTOROLA is not set
# CONFIG_USB_SERIAL_NAVMAN is not set
# CONFIG_USB_SERIAL_PL2303 is not set
# CONFIG_USB_SERIAL_OTI6858 is not set
# CONFIG_USB_SERIAL_QCAUX is not set
# CONFIG_USB_SERIAL_QUALCOMM is not set
# CONFIG_USB_SERIAL_SPCP8X5 is not set
# CONFIG_USB_SERIAL_HP4X is not set
# CONFIG_USB_SERIAL_SAFE is not set
# CONFIG_USB_SERIAL_SIEMENS_MPI is not set
# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set
# CONFIG_USB_SERIAL_SYMBOL is not set
# CONFIG_USB_SERIAL_TI is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
# CONFIG_USB_SERIAL_OPTION is not set
# CONFIG_USB_SERIAL_OMNINET is not set
# CONFIG_USB_SERIAL_OPTICON is not set
# CONFIG_USB_SERIAL_VIVOPAY_SERIAL is not set
# CONFIG_USB_SERIAL_DEBUG is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_SEVSEG is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
CONFIG_USB_APPLEDISPLAY=m
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_GADGET is not set

#
# OTG and related infrastructure
#
# CONFIG_NOP_USB_XCEIV is not set
# CONFIG_UWB is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y

#
# LED drivers
#
# CONFIG_LEDS_PCA9532 is not set
# CONFIG_LEDS_LP3944 is not set
# CONFIG_LEDS_PCA955X is not set
# CONFIG_LEDS_BD2802 is not set
CONFIG_LEDS_TRIGGERS=y

#
# LED Triggers
#
# CONFIG_LEDS_TRIGGER_TIMER is not set
CONFIG_LEDS_TRIGGER_IDE_DISK=y
# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
CONFIG_LEDS_TRIGGER_DEFAULT_ON=y

#
# iptables trigger is under Netfilter config (LED target)
#
# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
# CONFIG_RTC_CLASS is not set
# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set

#
# TI VLYNQ
#
# CONFIG_STAGING is not set

#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
# CONFIG_EXT2_FS_POSIX_ACL is not set
# CONFIG_EXT2_FS_SECURITY is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_EXT4_FS=y
CONFIG_EXT4_FS_XATTR=y
# CONFIG_EXT4_FS_POSIX_ACL is not set
# CONFIG_EXT4_FS_SECURITY is not set
# CONFIG_EXT4_DEBUG is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_JBD2=y
# CONFIG_JBD2_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set

#
# Caches
#
# CONFIG_FSCACHE is not set

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
# CONFIG_MSDOS_FS is not set
# CONFIG_VFAT_FS is not set
# CONFIG_NTFS_FS is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_LOGFS is not set
# CONFIG_CRAMFS is not set
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
# CONFIG_NETWORK_FILESYSTEMS is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
# CONFIG_SYSV68_PARTITION is not set
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=m
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
CONFIG_NLS_ISO8859_1=m
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=m
# CONFIG_DLM is not set
# CONFIG_BINARY_PRINTF is not set

#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_GENERIC_FIND_LAST_BIT=y
CONFIG_CRC_CCITT=y
CONFIG_CRC16=y
CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_LZO_DECOMPRESS=y
CONFIG_DECOMPRESS_GZIP=y
CONFIG_DECOMPRESS_BZIP2=y
CONFIG_DECOMPRESS_LZMA=y
CONFIG_DECOMPRESS_LZO=y
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y

#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
CONFIG_DETECT_HUNG_TASK=y
# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
CONFIG_SCHEDSTATS=y
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_SLUB_DEBUG_ON is not set
# CONFIG_SLUB_STATS is not set
# CONFIG_DEBUG_KMEMLEAK is not set
CONFIG_DEBUG_PREEMPT=y
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
CONFIG_STACKTRACE=y
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_HIGHMEM is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_WRITECOUNT is not set
CONFIG_DEBUG_MEMORY_INIT=y
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
# CONFIG_DEBUG_CREDENTIALS is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_LKDTM is not set
# CONFIG_FAULT_INJECTION is not set
CONFIG_LATENCYTOP=y
CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_RING_BUFFER=y
CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
# CONFIG_PROFILE_ALL_BRANCHES is not set
# CONFIG_STACK_TRACER is not set
# CONFIG_KMEMTRACE is not set
# CONFIG_WORKQUEUE_TRACER is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_RING_BUFFER_BENCHMARK is not set
# CONFIG_DYNAMIC_DEBUG is not set
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
# CONFIG_PPC_DISABLE_WERROR is not set
CONFIG_PPC_WERROR=y
CONFIG_PRINT_STACK_DEPTH=64
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_PPC_EMULATED_STATS is not set
# CONFIG_CODE_PATCHING_SELFTEST is not set
# CONFIG_FTR_FIXUP_SELFTEST is not set
# CONFIG_MSI_BITMAP_SELFTEST is not set
CONFIG_XMON=y
CONFIG_XMON_DEFAULT=y
CONFIG_XMON_DISASSEMBLY=y
CONFIG_DEBUGGER=y
CONFIG_IRQSTACKS=y
# CONFIG_VIRQ_DEBUG is not set
# CONFIG_BDI_SWITCH is not set
CONFIG_BOOTX_TEXT=y
# CONFIG_PPC_EARLY_DEBUG is not set

#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
# CONFIG_DEFAULT_SECURITY_SELINUX is not set
# CONFIG_DEFAULT_SECURITY_SMACK is not set
# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
CONFIG_DEFAULT_SECURITY_DAC=y
CONFIG_DEFAULT_SECURITY=""
CONFIG_CRYPTO=y

#
# Crypto core or helper
#
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=y
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_BLKCIPHER2=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_PCOMP=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_MANAGER2=y
# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_WORKQUEUE=y
# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_AUTHENC=y
# CONFIG_CRYPTO_TEST is not set

#
# Authenticated Encryption with Associated Data
#
# CONFIG_CRYPTO_CCM is not set
# CONFIG_CRYPTO_GCM is not set
# CONFIG_CRYPTO_SEQIV is not set

#
# Block modes
#
CONFIG_CRYPTO_CBC=y
# CONFIG_CRYPTO_CTR is not set
# CONFIG_CRYPTO_CTS is not set
CONFIG_CRYPTO_ECB=m
# CONFIG_CRYPTO_LRW is not set
CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_XTS is not set

#
# Hash modes
#
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
# CONFIG_CRYPTO_VMAC is not set

#
# Digest
#
CONFIG_CRYPTO_CRC32C=m
# CONFIG_CRYPTO_GHASH is not set
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=m
# CONFIG_CRYPTO_RMD128 is not set
# CONFIG_CRYPTO_RMD160 is not set
# CONFIG_CRYPTO_RMD256 is not set
# CONFIG_CRYPTO_RMD320 is not set
CONFIG_CRYPTO_SHA1=y
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m

#
# Ciphers
#
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_BLOWFISH=m
# CONFIG_CRYPTO_CAMELLIA is not set
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_FCRYPT is not set
CONFIG_CRYPTO_KHAZAD=m
# CONFIG_CRYPTO_SALSA20 is not set
# CONFIG_CRYPTO_SEED is not set
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m

#
# Compression
#
CONFIG_CRYPTO_DEFLATE=m
# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set

#
# Random Number Generation
#
# CONFIG_CRYPTO_ANSI_CPRNG is not set
CONFIG_CRYPTO_HW=y
# CONFIG_CRYPTO_DEV_HIFN_795X is not set
# CONFIG_PPC_CLOCK is not set
# CONFIG_VIRTUALIZATION is not set

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Joseph Jezak]

>> Okay, so we fixed the first thing. That's good. :) Can you attach your
>> whole kernel config? I'm wondering if maybe udev isn't running properly
>> due to a misconfiguration.
>>
>> -Joe
> Attached unless GMail does something to it.
>
> Thanks,
> Mark

Another busy week, but I think we might have your answer.

Disable these options in your kernel config, recompile and give it a try:
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y

I think these options interfere with udev.
-Joe

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Thu, Oct 7, 2010 at 10:34 AM, Joseph Jezak <josejx@gentoo.org> wrote:
>
>>> Okay, so we fixed the first thing. That's good. :) Can you attach your
>>> whole kernel config? I'm wondering if maybe udev isn't running properly
>>> due to a misconfiguration.
>>>
>>> -Joe
>> Attached unless GMail does something to it.
>>
>> Thanks,
>> Mark
>
> Another busy week, but I think we might have your answer.
>
> Disable these options in your kernel config, recompile and give it a try:
> CONFIG_SYSFS_DEPRECATED=y
> CONFIG_SYSFS_DEPRECATED_V2=y
>
> I think these options interfere with udev.
> -Joe

Thank you Joe. For the first time in a couple of months the machine just booted.

Note that I didn't easily find  CONFIG_SYSFS_DEPRECATED in make
menuconfig so I only disabled  CONFIG_SYSFS_DEPRECATED_V2 which was
enough to allow it to boot.

I took a quick look at the PPC install guide and frankly I don't see
instructions there to disable this option, although I have done this
on other machines. Is it just me or are the instructions actually not
in the kernel config section. If they are truly missing then it would
be great if someone could update that.

Anyway, it seems completely unreasonable for me, after all this, to
just say thanks for the help. It doesn't begin to represent how
appreciative I am of the time you spent looking into this with me. I
really am indebted.

Cheers,
Mark

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Joseph Jezak]

 On 10/07/10 14:29, Mark Knecht wrote:
> On Thu, Oct 7, 2010 at 10:34 AM, Joseph Jezak <josejx@gentoo.org> wrote:
>>>> Okay, so we fixed the first thing. That's good. :) Can you attach your
>>>> whole kernel config? I'm wondering if maybe udev isn't running properly
>>>> due to a misconfiguration.
>>>>
>>>> -Joe
>>> Attached unless GMail does something to it.
>>>
>>> Thanks,
>>> Mark
>> Another busy week, but I think we might have your answer.
>>
>> Disable these options in your kernel config, recompile and give it a try:
>> CONFIG_SYSFS_DEPRECATED=y
>> CONFIG_SYSFS_DEPRECATED_V2=y
>>
>> I think these options interfere with udev.
>> -Joe
> Thank you Joe. For the first time in a couple of months the machine just booted.
>
> Note that I didn't easily find  CONFIG_SYSFS_DEPRECATED in make
> menuconfig so I only disabled  CONFIG_SYSFS_DEPRECATED_V2 which was
> enough to allow it to boot.
>
> I took a quick look at the PPC install guide and frankly I don't see
> instructions there to disable this option, although I have done this
> on other machines. Is it just me or are the instructions actually not
> in the kernel config section. If they are truly missing then it would
> be great if someone could update that.
>
> Anyway, it seems completely unreasonable for me, after all this, to
> just say thanks for the help. It doesn't begin to represent how
> appreciative I am of the time you spent looking into this with me. I
> really am indebted.
>
> Cheers,
> Mark
>
>
No problem! I'm glad it's working. The documentation has not been
updated recently, and it's on my list of things to do. Unfortunately, so
are a lot of other things. :) I've added it to my documentation fix it
list, I'll make sure to get this added to the documentation as soon as I
find some free time.

Most people aren't hit by the bug because when udev is installed, it
warns that these options will cause problems. You got lucky I guess! :)

Glad you stuck with it!
-Joe

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Klaus Müller]

Am 23.09.10 00:59, Mark Knecht wrote:
>[snip]
>Can anyone see what I've done wrong?

Most likely nothing at all.

Your hd may be faulty.
I had a problem with such a hd some time ago
(not on PPC, and a really old hd btw).

No error was found by any hd-check.

[X]Ubuntu and Puppy installed, booted and worked fine,
Gentoo installed fine but refused to boot.

After replacing the hd, Gentoo installed, booted and works.

Re: [gentoo-ppc-user] yaboot has kicked my butt - 5 times?!

[Mark Knecht]

On Sun, Sep 26, 2010 at 9:48 AM, Klaus Müller <mk.2001@web.de> wrote:
> Am 23.09.10 00:59, Mark Knecht wrote:
>>[snip]
>>Can anyone see what I've done wrong?
>
> Most likely nothing at all.
>
> Your hd may be faulty.
> I had a problem with such a hd some time ago
> (not on PPC, and a really old hd btw).
>
> No error was found by any hd-check.
>
> [X]Ubuntu and Puppy installed, booted and worked fine,
> Gentoo installed fine but refused to boot.
>
> After replacing the hd, Gentoo installed, booted and works.
>
>

Well, that's sort of scary but exactly describes my predicament!

Thanks,
Mark