[gentoo-dev] OpenRC + Bridge + Tap not working as expected?

[gentoo-dev] OpenRC + Bridge + Tap not working as expected?

[Ed W]

Hi, I am using openrc 0.4.2 and trying to setup a bridge for use with
openvpn.  Starting the bridge (/etc/init.d/br0 start) doesn't seem to be
correctly bringing up the dependent interfaces (should it?)

When I try and bring up my bridge I get only this:

# /etc/init.d/br0 start
* Bringing up interface br0
*   Destroying bridge br0...
*     Removing port eth0... [ ok ]
 [ ok ]
*   Creating bridge br0...
*   Adding ports to br0
*     eth0... [ ok ]
*     tap0...SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
interface tap0 does not exist!
SIOCGIFFLAGS: No such device
 [ !! ]
* ERROR: net.br0 failed to start

then I check:

#ifconfig
eth0      Link encap:Ethernet  HWaddr 00:1b:21:19:09:8d
          inet6 addr: fe80::21b:21ff:fe19:98d/64 Scope:Link
          UP BROADCAST RUNNING PROMISC MULTICAST  MTU:1500  Metric:1
          RX packets:9717 errors:4 dropped:0 overruns:0 frame:2
          TX packets:5923 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:1326386 (1.2 MiB)  TX bytes:1079556 (1.0 MiB)
          Base address:0xa000 Memory:e9020000-e9040000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:4243 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4243 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:570436 (557.0 KiB)  TX bytes:570436 (557.0 KiB)

(Curious eth0 is up... Lets try and stop it)
#/etc/init.d/net.eth0 stop

* WARNING: net.eth0 is already stopped


If I simply start the tap0 and eth0 interfaces deliberately first then
everything runs fine.  My understanding though is that the bridge should
bring up dependent interfaces?

Config in /etc/conf.d/net

config_eth0=( "null" )
tuntap_tap0="tap"
config_tap0=( "0.0.0.0 promisc" )
bridge_br0="eth0 tap0"
config_br0=( "192.168.105.4/24" )
routes_br0=( "default via 192.168.105.254" )
# Make the bridge depend on tap0 / eth0
RC_NEED_br0="net.eth0 net.tap0"


Any suggestions on how to fix?

Thanks

Ed W

Re: [gentoo-dev] OpenRC + Bridge + Tap not working as expected?

[Josh Saddler]

[-- Attachment #1: Type: text/plain, Size: 167 bytes --]

This list is not a user support list. Please see the gentoo-user ML. You
may also want to check http://forums.gentoo.org to see if anyone else
has had the issue.


[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 197 bytes --]