Yep, that was in the linksys readme on the driver.
It executes without error.

On Mon, 2002-12-09 at 13:28, Per-Erik Westerberg wrote:

    Hi,
    
    Have you tried issuing the command ...
    
    "modprobe prism2_usb prism2_doreset=1" 
    
    ... to load the proper module before starting the wlan-usb-thing?
    
      Regards / Per-Erik
    
    On Mon, 2002-12-09 at 18:59, Adam Voigt wrote:
    > Alright, well, this:
    > 
    > cat /proc/pci | grep "usb"
    > 
    > Returns bupkiss, but should the usb be mentioned
    > in /proc/pci? It's on the motherboard so shouldn't it
    > not be in there anyway, or is "pci" misleading in that
    > it means all devices?
    > 
    > (Last time I bug you, promise.) =)
    > 
    > On Mon, 2002-12-09 at 12:52, Tom Prado wrote:
    > 
    >     On 9 Dec 2002, Adam Voigt wrote:
    >     
    >     > dmesg | grep "usb" 
    >     > 
    >     > Produces:
    >     > 
    >     > usb.c: registered new driver usbdevfs
    >     > usb.c: registered new driver hub
    >     > init_module: prism2_usb.o: 0.1.16-pre7 Loaded
    >     > init_module: dev_info is: prism2_usb
    >     > usb.c: registered new driver prism2_usb
    >     > 
    >     > And no, there is nothing in /proc/bus/usb.
    >     > 
    >     > Modprobing usb-uhci, uhci, or usb-ohci all throw error's and
    are
    >     not
    >     > inserted.
    >     > However, usb-core is loaded automatically when I modprobe
    the
    >     prism2
    >     > driver.
    >     
    >     hmm, that's not good that all the ?hci drivers return errors. 
    You
    >     don't 
    >     appear to have any USB bus drivers loaded.  See which USB
    adapter
    >     you have 
    >     by doing a cat /proc/pci (or use lspci) and look for the USB
    >     devices.
    >     
    >     I.e. mine are:
    >     
    >     00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1)
    (rev
    >     02)
    >     00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2)
    (rev
    >     02)
    >     00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3)
    (rev
    >     02)
    >     
    >     and dmesg | grep usb returns:
    >     
    >     usb-uhci.c: $Revision: 1.275 $ time 23:33:42 Dec  4 2002
    >     usb-uhci.c: High bandwidth mode enabled
    >     usb-uhci.c: USB UHCI at I/O 0xefe0, IRQ 11
    >     usb-uhci.c: Detected 2 ports
    >     
    >     You might want to check out
    >     http://www.linux-usb.org/USB-guide/book1.html 
    >     
    >     Best of luck,
    >     Tom
    >     
    >     
    >     --
    >     gentoo-dev@gentoo.org mailing list
    > 
    >     
    > 
    > -- 
    > Adam Voigt (adam@cryptocomm.com)
    > The Cryptocomm Group
    > My GPG Key: http://64.238.252.49:8080/adam_at_cryptocomm.asc
    
    
    
    --
    gentoo-dev@gentoo.org mailing list
    

-- 
Adam Voigt (adam@cryptocomm.com)
The Cryptocomm Group
My GPG Key: http://64.238.252.49:8080/adam_at_cryptocomm.asc