* Re: [gentoo-desktop]
2010-01-26 16:11 [gentoo-desktop] Adam Mooz
2010-01-26 17:18 ` [gentoo-desktop] Dale
@ 2010-01-27 0:52 ` Lindsay Haisley
1 sibling, 0 replies; 5+ messages in thread
From: Lindsay Haisley @ 2010-01-27 0:52 UTC (permalink / raw
To: gentoo-desktop
On Tue, 2010-01-26 at 11:11 -0500, Adam Mooz wrote:
> unsubscribe
Re: UNSUBSCRIBE
Please Note: In some later model unsubscribe kits, the "OFF" indicator has
been replaced by "POWER-UP STANDBY ENABLE". Accordingly the "ON" indicator
has been replaced by the much clearer, "POWER-DOWN STANDBY ENABLE". Contact
your internet service provider for a list of affected model numbers. An
"ON-OFF" retrofit panel kit is available for those who have difficulty with
the new and much clearer labeling.
First, ask your Internet Provider to mail you an Unsubscribing Kit. Then follow these
directions. The kit will most likely be the standard no-fault type. Depending on
requirements, System A and/or System B can be used. When operating System A, depress
lever and a plastic dalkron unsubscriber will be dispensed through the slot
immediately underneath. When you have fastened the adhesive lip, attach connection
marked by the large "X" outlet hose. Twist the silver- coloured ring one inch below
the connection point until you feel it lock.
The kit is now ready for use. The Cin-Eliminator is activated by the small switch on
the lip. When securing, twist the ring back to its initial condition, so that the two
orange lines meet. Disconnect. Place the dalkron unsubscriber in the vacuum receptacle
to the rear. Activate by pressing the blue button.
The controls for System B are located on the opposite side. The red release switch
places the Cin-Eliminator into position; it can be adjusted manually up or down by
pressing the blue manual release button. The opening is self- adjusting. To secure
after use, press the green button, which simultaneously activates the evaporator and
returns the Cin-Eliminator to its storage position.
You may log off if the green exit light is on over the evaporator . If the red light
is illuminated, one of the Cin-Eliminator requirements has not been properly
implemented. Press the "List Guy" call button on the right of the evaporator . He will
secure all facilities from his control panel.
To use the Auto-Unsub, first undress and place all your clothes in the clothes rack.
Put on the velcro slippers located in the cabinet immediately below. Enter the shower,
taking the entire kit with you. On the control panel to your upper right upon entering
you will see a "Shower seal" button. Press to activate. A green light will then be
illuminated immediately below. On the intensity knob, select the desired setting. Now
depress the Auto-Unsub activation lever. Bathe normally.
The Auto-Unsub will automatically go off after three minutes unless you activate the
"Manual off" override switch by flipping it up. When you are ready to leave, press the
blue "Shower seal" release button. The door will open and you may leave. Please remove
the velcro slippers and place them in their container.
If you prefer the ultrasonic log-off mode, press the indicated blue button. When the
twin panels open, pull forward by rings A & B. The knob to the left, just below the
blue light, has three settings, low, medium or high. For normal use, the medium
setting is suggested.
After these settings have been made, you can activate the device by switching to the
"ON" position the clearly marked red switch. If during the unsubscribing operation,
you wish to change the settings, place the "manual off" override switch in the "OFF"
position. You may now make the change and repeat the cycle. When the green exit light
goes on, you may log off and have lunch. Please close the door behind you.
--
Lindsay Haisley |"Fighting against human creativity is like trying
FMP Computer Services | to eradicate dandelions"
512-259-1190 |
http://www.fmp.com | - Pamela Jones of Groklaw
--
Lindsay Haisley | "Everything works if you let it"
FMP Computer Services |
512-259-1190 | - The Roadie
http://www.fmp.com |
^ permalink raw reply [flat|nested] 5+ messages in thread